CR Remeha Quinta Pro 115 Скачать руководство пользователя страница 68

Страница: 68 / 92

7.3.4.

Checking combustion

The check on combustion is done by measuring the percentage of

/CO

in the flue gas discharge flue. To do this, proceed as follows:

1. Unscrew the plug of the flue gas measurement point.
2. Connect the flue gas analyser.

CAUTION

Ensure that the opening around the sensor is completely

sealed when taking measurements.

3. Set the boiler to full load. Press the two

keys simultaneously.

The

symbol is visible on the menu bar and

appears in the

display. The boiler is now operating at full load.

4. Measure the percentage of CO

and compare this value with the

checking values given.

See chapter: "Setting the air/gas ratio (Full load)", page

50.

5. Set the boiler to part load. Press the

[-]

key several times until

is displayed on the screen. The boiler is now operating on

part load.

6. Measure the percentage of CO

and compare this value with the

checking values given.

See chapter: "Setting the air/gas ratio (Part load)", page

51.

T001581-A

T001631-B

...x

7. Checking and maintenance

Quinta Pro 30 - 45 - 65 - 90 - 115

250413 - 123157-03

Содержание Quinta Pro 115





























































































Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды

CR Remeha Quinta Pro 115, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды