CR Remeha Quinta Pro 115 Скачать руководство пользователя страница 42

Страница: 42 / 92

Jumper 2: The settings for central heating and sanitary hot water

are reversed.

4.9.7.

Connection possibilities for the PCB (SCU-
X03)

The control PCB SCU-X03 can control a modulating central heating

pump. Depending on the make and type of pump, the pump can be

controlled by a 0-10 V, 4-20 mA or PWM signal. The speed of the

pump is modulated, based on the signal received from the boiler.

For correct connection of the pump, see the documentation

supplied with the pump.

Connect on/off contact

Connect the on/off contact of the central heating pump to the

connector

CAUTION

Do not use the on/off contact to interrupt the power supply

to the pump.

Connect central heating pump

The control system of the central heating pump is connected to

connector

Select the type of signal that will be received from the boiler using the

rotary knob

SW1

on the control PCB. See table below:

No. Description

Pump modulation signal

Required heat output of boiler

Current heat output of boiler

T002038-B

SCU-X03

Ctrl

0 +

4. Installation

Quinta Pro 30 - 45 - 65 - 90 - 115

250413 - 123157-03

Содержание Quinta Pro 115





























































































Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды

CR Remeha Quinta Pro 115, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды