CR Remeha Quinta Pro 115 Скачать руководство пользователя страница 24

Страница: 24 / 92

4.6

Gas connection

WARNING

Close the main gas valve before starting work on the

gas pipes.

Before mounting, check that the gas meter has

sufficient capacity. To do this, you should keep in

mind the consumption of all appliances.

If the gas meter has a too low capacity, inform the

energy supply company.

1. Remove the anti-dust plug located on the gas connection

GAS/

GAZ

under the boiler.

2. Connect the gas inlet pipe.
3. Mount a gas isolation valve on this pipe, directly under the boiler.
4. Connect the gas pipe to the gas shut off valve.

CAUTION

Ensure that there is no dust in the gas pipe.

We recommend installing a gas filter on the gas pipe

to prevent clogging of the gas valve unit.

Connect the gas pipe in accordance with prevailing

standards and regulations.

4.7

Connections for the air and exhaust pipes

The boiler is suitable for the following types of flue gas

connections.

See chapter: "Certifications", page 8.

4.7.1.

Classification

The table specifies this classification in detail according to

[

Type

Execution

Description

B23
B23P

(1)

Open

Without fire-stop approval.

Exhaust of combustion gases above the roof.

Air in the installation room.

B33

Open

Without fire-stop approval.

Common exhaust of combustion gases above the roof.

Common exhaust of combustion gases mixed in the air, air in the installation room (special

construction).

C13

Closed

Vent in the outside wall.

The opening for the air-supply inlet is located in the same pressure zone as the vent (For

example, a common passage through the outside wall).

(1) Including the pressure classification P1

(2) EN483: 0,5 mbar suction by pressure reduction

(3) An under pressure of 4 mbar is possible

(4) See table for minimum sizes of duct or sleeving

T002859-C

4. Installation

Quinta Pro 30 - 45 - 65 - 90 - 115

250413 - 123157-03

Содержание Quinta Pro 115





























































































Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды

CR Remeha Quinta Pro 115, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды