CR Remeha Quinta Pro 115 Скачать руководство пользователя страница 22

Страница: 22 / 92

4.5

Hydraulic connections

4.5.1.

Flushing the system

The installation must be cleaned and flushed according to BS 7593

(2006).

Installing the boiler in new installations (installations less than
6 months old)

Clean the installation with a universal cleaner to eliminate debris

from the appliance (copper, hemp, flux).

Thoroughly flush the installation until the water runs clear and

shows no impurities.

Installing the boiler in existing installations

Remove sludge from the installation.

Flush the installation.

Clean the installation with a universal cleaner to eliminate debris

from the appliance (copper, hemp, flux).

Thoroughly flush the installation until the water runs clear and

shows no impurities.

Suitable chemicals and their use should be discussed with

specialist water treatment companies in respect to

aluminium heat exchangers.

4.5.2.

Connection of the heating circuit

1. Remove the anti-dust plug located on the heating outlet

connection

{

under the boiler.

2. Connect the heating water outlet pipe to the heating flow

connection.

3. Install a filling and drainage valve on the installation for filling and

draining the boiler.

T002856-C

4. Installation

Quinta Pro 30 - 45 - 65 - 90 - 115

250413 - 123157-03

Содержание Quinta Pro 115





























































































Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды

CR Remeha Quinta Pro 115, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды