background image

 

 

 [Document Title Name Goes Here] 

 

 

 

R900 Installation Guide 

 

The R900 bill validator is designed to fit into the standard bill acceptor opening 
in most vending machines and can be mounted on existing studs or a mounting 
bracket 

 

 

Features 

-

 

Four way bill acceptance 

-

 

Multi-width bill handling mechanism 

-

 

Lockable security cashbox (lockable) available 

 

Interface 

-

 

The R900 bill validator operates via MDB interface 

-

 

PC base; RS232C interface CCNET protocol is also available 

 

Operating Voltage 

-

 

34VDC/24VDC for MDB interface 

-

 

12VDC for CCNET interface (RS232C base) 

 
 
 
 

INSTALLATION 

 

Before installation, remove the R900 bill validator from the packaging and inspect for any physical damage. If damaged, contact 
technical support 

 

1.

 

Turn off power from the vending machine. 

2.

 

Remove the bill magazine. Press forward on the yellow latch on the bill magazine and pull to remove.  

3.

 

Mount the R900 bill validator on the mounting studs, through the opening in the front of the vendor and secure using the included 
hardware. 

4.

 

Connect the R900 bill validator to the appropriate interface harness. Apply gentle pressure to connect; the pins will bend if forced. 

5.

 

Turn on power to the vending machine. 

6.

 

Check the arrow LED on the front of R900. The LED should be flashing. In some cases, the machine door must be closed first. 

7.

 

Once the LED is flashing, test the validator with a bill. 

a.

 

Insert a bill and confirm that it stacks and credit is given 

b.

 

Repeat this process for any other enabled bills. 

8.

 

When your test is completed, remove the test bills from the bill magazine. 

 
 
 
 
The installation is now complete. Refer to the other sections of this guide to configure the device, if necessary. 

 

 

Содержание R900








Отзывы: