MCP737NG
FOREWORD
Thank you for purchasing CPflight MCP737NG hardware. To optimize the performance of this unit,
please read through this manual carefully. This manual gives you the information to connect and
use MCP737NG panel with FSX, P3d, Project Magenta, Prosim and other add-on software. Even if
the MCP737NG support the mainly used FS add-on software, it is not possible to assure the full
compatibility with all third part add-on. To know more about the compatibility with a specific add-on
aircraft please refer to the latest information on the “Technical and Manual” section at CPflight
website product page.
Note: This manual contains latest information at the time of drafting. Due to the continuous evolving
of the product some features could be been modified. Eventual later information can be found at
CPflight website www.cpflight.com
The CPflight modules are produced to meet requirements from the hobby market. The use of our
products in professional or commercial environments is not permitted without approval of the
CPflight management; please contact us at [email protected] if you need to exploit our products in
professional or commercial environments.
MCP737NG is a full scale replica of the Boeing 737NG Mode Control Panel, look and functionality
are reproduced with high details. MCP737NG is equipped with high quality level components: high
reliability encoders, autothrottle ARM switch with electromagnetic disengage and bank selector
knob gives a high fidelity performances and a never seen realism.
IMPORTANT NOTE: It is important to know that the hardware have not its own intelligence
on board, it establishes an interface with the connected software; logics, operating modes
and aircraft behavior are managed by the software itself.
HARDWARE INSTALLATION
The MCP737NG is designed for panel assembly. The MCP737NG is intended as a part to be
inserted in a cockpit reproduction, CPflight does not produce chassis or other mechanical parts for
the cockpit structure, so the panel is intended to be inserted in your own cockpit glare shield. Fixing
screws are not provided as depending by the thickness and/or material of your glare shield panel,
different screws can be required.
In your glare shield structure maintain the accessibility to the back of the MCP to allows working to
the connections.
CONNECTIONS
The MCP is provided with a universal supply adapter that accepts a voltage of 100 to 240Vac
(50/60Hz). Supply adapter and USB cable are provided with the MCP, you don’t need further
hardware to operate.
Sockets for connections are on the back of panel. Beyond to the supply and USB connectors the
MCP737NG have some further sockets, they are provided to allow system expandability. A DIN 5
pole socket “C” is used to link auxiliary CPflight modules (Efis Selectors, Radios etc.)
A small terminal block allows connections for external backlight control, external A/T disengage
pushbutton and external TO/GA pushbutton.
A - Power supply socket
B - USB
C - 5 poles DIN socket for external module connection
D - external controls
WARNING! Do not attempt to connect anything different from as described in this section;
warranty does not cover damages due to incorrect wiring of any external device. The
MCP737NG is provided with 6Vdc power supply adapter. Only provided stabilized plug-in
power supply adapter must be used; do not attempt to plug in a different adapter because
you can damage the MCP. The provided adapter is suitable for 100 to 240 Vac 50/60Hz main
supply.
Note: If you do not use MCP for a long time it is recommended to disconnect the power
supply.
Note: Further information about the following sections on the “MCP737NG Getting Started”
document at the MCP737NG “Technical and Manual” section on cpflight website
USB DRIVER INSTALLATION
For this operation and compatible addon please refer also to the MCP737NG_Getting_Started.pdf
document
https://www.cpflight.com/docs/prodotti/2/MCP737NG_Getting_Started.pdf
When you connect the MCP737NG for the first time, the operative system start to automatically
search the USB driver. Usually the right USB driver already is on PC with windows7 or later, after
few second find and install the usb driver. If the driver is not on the PC, you can download at
Cpflight website (see “MCP737NG Getting Started” document)
During the USB drivers installation the system assign a number to the communication port. Check
your configuration in the Windows Control panel -> System Property -> Device Manager Tab.
On the (COM & LPT) port you will see “CPflight serial adapter (COM n)” where “n” is the assigned
communication port number, you will use this number in the First set up (see following).
COMMUNICATION SOFTWARE INSTALLATION
Besides the USB drivers a comunication software is needed to use the MCP737NG with default FS-
P3d.
Note: the comunication software allows to use the MCP737NG with default FS-P3d aircraft. To use
the MCP737NG with other add-on software follow the related instructions.
To install the comunication software:
- Download instfsx_xxx.zip (for FSX) or inst P3D_xxx where xxx = revision number.
- The file is in a compressed (zip) archive. Extract in a temporary folder and run the exe file to install
software (start PC as administrator to install software on Windows).
- CPflight MCP requires the popular FSUIPC library. If you do not have FSUIPC in your system
download it at http://www.schiratti.com/dowson.html.
FIRST SET UP AND START-UP
Note for Project Magenta users: To enable communication with Project Magenta set the
communication port number in the Project Magenta “mcp.ini” file. In the Project Magenta MCP
folder open “mcp.ini” with a text editor, browse the [Serial Connection] section and set
CpflightComm= n in where “n” is the communication port assigned by the system during the USB
drivers installation. Save the “mcp.ini” file. To start-up the MCP737NG run Project Magenta MCP
software.
To start the MCP737NG with default FS-P3d select “Connect” in the FS-P3d Add-on menu ->
CPflight -> FS-COM. The first time you run FS-COM you will ask to select in the communication
port number (Setting COM); set the port number assigned during the USB driver installation (see
above).
At the start-up, the MCP737NG will show on the left “COURSE” and “IAS/MACH” displays the
product serial number while the right “COURSE” display shows the installed Firmware revision.
The MCP turns off command come from the computer when you close the software. If you shut-
down the computer without exit the software or a computer block occur, the MCP may stay on or
may fail the subsequent turn on. If you find any problem with the MCP start or turn off, it is advisable
to reset the unit. To do this, disconnect the power supply and USB cable from the MCP, wait few
seconds then reconnect power and USB.
Important note: MCP can extinguishes the displays to simulate a “cold and dark” situation
depending by the battery, avionics or other aircraft system status.
A/T ARM SWITCH
MCP737NG comes provided with electromagnetic Autothrottle ARM switch. The switch
automatically releases to the “Off” position after the landing touchdown or pressing an external
disengage button (see “Expansions” section). The switch releases command is sent by the
software; the software can switch off the A/T ARM switch also for different reason depending by the
status of aircraft systems (fault detected etc.). If the A/T switch does not stay in the “On” position
check aircraft conditions. The A/T ARM switch also can be manually disengaged.
ON-FLY DISPLAY BRIGHTNESS AND BACKLIGHT REGULATION
When the MCP is normal running (starts with Project Magenta, PMDG or in test mode using the
CPflight test software) you can on-fly set the display and backlight brightness. These functions are
not available if the related preferences are settled "On" in the configuration menu (see above
“CONFIGURATION MODE” section). To change the display brightness hold pushed the C/O button
and rotates the HDG knob; to regulate the backlight brightness hold pushed the C/O button and
rotates the ALTITUDE knob. The MCP keep the regulation in its working memory, data are saved in
a non-volatile memory when the MCP turn-off (data are not saved if you disconnect the MCP power
supply during the normal running).
CONFIGURATION MODE
MCP737NG firmware provides an internal program mode to configure some preferences in the
hardware functionality. With the MCP in stand-by (software not running) push and hold the C/O key
for more than 1 second; this start the hardware in configuration mode. This is the only way to
access to the configuration mode; no PC software program is required to configure the MCP737NG
hardware. In program mode only some keys are operating; the Left Course, IAS and Right Course
displays shows the program title and option to set the parameters.
C/O key (push and hold for more than 1 second): enter the program menu.
N1 key: scroll to the next program menu.
ENCODERS COURSE 2: set the preferences.
C/O key: save changes and exit the program menu.
Settings are saved in a non-volatile memory when you exit the configuration menu and the MCP
goes in stand-by. Following a description of the menu available in Configuration Mode.
CONFIGURATION MENU
Left COURSE
display
IAS/MACH
display
Right COURSE
display
BACKLIGHT CONTROL: allow to select how to
manage the backlight control:
I : (default) the backlight will light-up when the NAV
lights in FS are ON.
E: the NAV lights status will be skipped and the
backlight can be controlled through the related auxiliary
input.
ICS: only operate in conjunction with the CPflight “ICS”
board system (option). With this setting the MCP
backlight is bound to the Cockpit lights brightness
control panel (Captain “MAIN PANEL” bright)
bL
Ctrl
I/E/ICS
COUNTER: This menu show the Hours of MCP running.
It is a read only location and is not modifiable.
Note: the “xxxxx” in the above menu act for the total
Hours of MCP running from 0 to 9999.
HCn
xxxx
SERIAL NUMBER: This menu show the device serial
number. It is a read only location and is not modifiable.
xxx
xxxx
Ser
FIRMWARE RELEASE: This menu displays the
installed firmware release. The number is not modifiable
in this menu, but it is updated when you load a new
firmware in the MCP internal memory (see “FIRMWARE
UPDATE” section).
Fir
rEL
xxx
A
C
B
D