GREAT BRITAIN • CUSTOMER SERVICE
tel. 020 8247 9300 e-mail [email protected] internet www.clasohlson.co.uk
Ver
. 20150518
Remote Switch Set 3-Pack
Art.no 18-1255
Model 3
×
5105 50027
36-6010
3
×
51 50027
Please read the entire instruction manual before using the product and
then save it for future reference. We reserve the right for any errors in
text or images and any necessary changes made to technical data.
In the event of technical problems or other queries, please contact our
Customer Services.
Safety
• This product is suitable for switching products such as lights on
and off.
• Make sure that the light is turned off before connecting it to
the product.
• Never connect a light with a higher power rating than 1000 W.
• This product is intended for indoor use, do not expose it to rain or
moisture.
Operating instructions
Remote switch (receiver)
4. Pair the receiver to the transmitter by following the instructions
accompanying the transmitter. Up to 6 transmitters can be paired
with the receiver.
Unpairing one paired transmitter
1. Hold in the button on the front of the receiver which you want to
unpair the transmitter from for 3 seconds and then release it.
2. The LED inside the button will start to flash slowly. The receiver is
now ready to unpair from the transmitter.
3. Press in the [ OFF ] button on the transmitter (make sure to choose
the correct [ OFF ] button if the transmitter can connect to multiple
receivers). The transmitter will now unpair from the receiver.
Note:
The light can also be switched on/off manually by pressing
the button on the receiver.
Care and maintenance
• Unplug the receiver from the wall socket and remove the battery
from the transmitter they are not to be used for an extended period.
• Clean the product by wiping it with a dry cloth.
Troubleshooting guide
The remote
switch set is
not working.
• Has the receiver been paired with a transmitter
as described above? Try pairing them again.
• Check the battery in the transmitter.
• Is the transmitter too far away from the receiver
(25 m)?
• Check that the light is properly plugged into the
receiver and that it is switched on and not faulty.
• Try plugging the light into another electrical
outlet to make sure that it works.
• Is there electricity in the outlet the receiver is
plugged into?
Disposal
This product should be disposed of in accordance with local regulations.
If you are unsure how to proceed, contact your local council.
Specifications
Frequency
433.92 MHz
Receiver
Rated voltage
230 V, 50 Hz
Max range
25 m
Max load
1000 W
Transmitter
Battery
1 × A23, 12 V DC (included)
Number of channels
4
1. Plug the receiver into a wall
socket.
2. Hold in the button on the front
of the receiver for at least
3 seconds and then release it.
3. The LED inside the button will
start to flash slowly. The receiver
is now ready to be paired with
a transmitter.
5. Plug a light (or other load device
up to 1 kW) into the receiver and
check that the light is switched on.
Remote control (transmitter)
1. Remove the battery cover from
the back of the transmitter and
insert the included battery.
Note:
More than one transmitter
can be paired with the same
button, e.g. [ A ]. This can be
useful if you want to switch
on all the lights in a room at
the same time.
4. Use the buttons in the left-hand
“ON” row to switch the paired light
on and the buttons in the right-
hand “OFF” row to switch
the light off.
Unpairing all paired transmitters
1. Hold in the button on the front of
the receiver for 6 seconds until
the LED inside the button starts to
flash quickly.
2. When the LED stops flashing, all
the transmitters which were paired
with it will have been unpaired.
2. Make sure that the receiver that you are going to pair with is ready
to be paired with the transmitter (refer to the steps above).
3. Press in the button (A, B, C or D) in the left-hand “ON” row which
you want to control the receiver that you are pairing. The receiver
and transmitter will then pair. Follow the same procedure with
the other receivers.
