background image

  

 1 

 

 

Corsham Technologies, LLC 

www.corshamtech.com 

617 Stokes Road, Suite 4-299 

Medford, NJ  08055 

 

KIM Clone User Manual 

Revision 5 and later Boards 

 

Introduction 

 
Thank you for buying our KIM Clone board, which provides an almost identical look-
and-feel to the original MOS Technologies KIM-1 computer. 
 
This board should be very compatible with the original KIM-1 but is not exactly the 
same, so there might be a few programs that won’t work on it.  However, we’re kept 
the hardware very similar and preserved the entry points to all the major 
subroutines in the KIM monitor.  Some functionality has been removed, such as the 
cassette interface, so any code that makes direct calls to cassette storage/retrieval 
functions will not work. 

Overview 

 
The KIM Clone has a lot of features packed into it while still employing a fairly 
standard design with commonly available parts. 
 

 

RAM from 0000 to 13FF.  The original KIM-1 had only 0000 to 03FF. 

 

EEPROM from 1800 to 1FFF containing a modified KIM monitor. 

 

6530-like I/O, timer and RAM like the original KIM. 

 

RAM from 2000 to DFFF. 

 

Either RAM or EEPROM from E000 to FFFF. 

 

Vectors can point to either the original KIM monitor or your own code. 

 

No cassette interface for program storage. 

 

The spare 6532 has a header for connection to a Corsham Tech SD Card 
System. 

Содержание KIM Clone
















Отзывы: