CORNING Everon 6000 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 75

background image

User Manual v1.0

Corning Restricted and Confidential Proprietary - Controlled content

UM - Everon 6000 DAS - 19-DEC-2020.docx| December 2020

|Page 57 of 170

2.3.6

Connect Fiber SFP+

Note: use SFP+ from the approved list provided by Corning.

1.

Remove the rubber stopper from the source port.

2.

Push the SFP+ connector into the port, until it clicks (note that there is only one correct direction for
plugging-in).

3.

Remove the white plug-protectors from the end of the SFP+ cable.

4.

Plug the SFP+ cable into the D-MRU port until it clicks.

5.

connect the other edge of the cable to the source unit

Figure 8 Remove rubber stopper from port and from SFP+ Pluggable Transceiver and insert the SFP+ Pluggable

Transceivers (hot-pluggable optical transceiver module) into the port.

SFP+ Pluggable
Transceivers

SFP+ Cable

«
...
55
56
57
58
59
...
»

Содержание Everon 6000












































































Отзывы:

Нет отзывов

Похожие инструкции для Everon 6000

Бренд: H3C Страницы: 7

Бренд: Kathrein Страницы: 3

Бренд: M2 Antenna Systems Страницы: 5

Бренд: Parsec Technologies Страницы: 19

Бренд: TERK Technologies Страницы: 18

Бренд: Philex Страницы: 8

Бренд: RFI Страницы: 2

Бренд: Maco Antennas Страницы: 9

Бренд: WADE Antenna, Inc. Страницы: 2

Бренд: Etec Страницы: 8

Бренд: TP-Link Страницы: 2

Бренд: TP-Link Страницы: 6

Бренд: TP-Link Страницы: 12

Бренд: Cabletech Страницы: 24

Бренд: ClearStream Страницы: 2

Xtreme HD8200XL

Бренд: Solid Signal Страницы: 9

Бренд: Ubiquiti Страницы: 24

Бренд: Laird Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды