Cornelius VIPER E Скачать руководство пользователя

Страница: 64 / 66

Viper Low overrun Service Manual

Publication Number: 621360241LOEWSE

- 58 -

ROUBLESHOOTING

RODUCT

OLD

Problem

Probable Cause

Remedy

Compressor not Running

A. Barrel not in ON mode.
B. No voltage to compressor.

C. Bad start components.
D. Compressor’s thermal overload

protector “open”.

E. Open or shorted compressor wind-

ings.

F. Bad control board.

A. Turn barrel to ON.
B. Check power at contactor L1, L2 -

T1, T2.

C. Check components and wiring.
D. Check resistance of compressor

windings and check incoming line
voltage.

E. Check resistance of compressor

windings.

F. Troubleshoot, replace if necessary.

Compressor Running but
not Cooling

A. Low refrigerant.

B. Restricted condenser/filter.
C. Condenser fan motor/blade defec-

tive.

D. Hot gas valve leaking or open.
E. Defective compressor.

A. Repair leak and weigh in new

charge.

B. Clean or repair.
C. Repair or replace.

D. Replace.
E. Repair or replace.

Restricted Air Flow

A. Dirty filter.
B. Dirty condenser.
C. Damaged fins.
D. Not enough “clearance” around

unit.

A. Clean filter.
B. Clean condenser.
C. Repair/replace if necessary.
D. Ensure proper spacing around unit.

Fan Motor

A. Bad connection
B. Bad motor
C. Cracked or bent fan blade

A. Check/connect
B. Replace motor
C. Replace fan blade

Hot Gas Valve

A. Miswired.
B. Defective coil.
C. Defective product delivery board.

A. Correct wiring.
B. Replace coil.
C. Replace.

No/Low Refrigerant

A. Leak.

A. Repair and weigh in new charge.

Sensors

A. Bad connection.
B. Bad sensor.
C. Sensor out of position.
D. Defective product delivery board.

A. Correct wiring.
B. Replace sensor.
C. Reposition sensor and clip.
D. Replace.

Содержание VIPER E



































































Результаты поиска

Содержание VIPER E

Отзывы:

Похожие инструкции для VIPER E

Бренды по названию

Популярные бренды

Cornelius VIPER E, Руководство по обслуживанию

Результаты поиска

Содержание VIPER E

Отзывы:

Похожие инструкции для VIPER E

Бренды по названию

Популярные бренды