Cormach 50000 WB 50000 WB80 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 49

Cormach 50000 WB 50000 WB80 Скачать руководство пользователя страница 41



UT

Handbook for Use and Maitenance – 50000 WB-80-87-95

Edition

01/11

Revisione

00

41

50000WB_e111_E.doc

IMPORTANT NOTE:

NEVER WELD OR DRILL THE LOAD BEARING

STRUCTURES.

FOR MAINTENANCE OPERATIONS ON THE HYDRAULIC SYSTEM,

SUPPORT THE BOOM AND RELEASE THE PRESSURE.

BEFORE DISMOUNTING THE VALVES FROM THE CYLINDER, RELEASE

THE PRESSURE BY COMPLETELY SLACKENING THE REGISTERS.

CAREFUL REGULAR MAINTENANCE WILL EXTEND THE LIFE OF THE CRANE
AND MAKE IT SAFER.

3.5 - MAINTENANCE TO BE CARRIED OUT AFTER A LONG PERIOD OF
INACTIVIT

In case the crane is not going to be used for a long period of time, it will be
necessary to use the following precautions:

•

Verify the level of the oil inside the oil-tank if necessary add oil;

•

Eliminate condensation from inside tank oil;

•

Verify functioning of electric and safety devices.

«
...
39
40
41
42
43
...
»

Содержание 50000 WB 50000 WB80


















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды