background image

 

User and Maintenance Manual 

“E” Failsafe caliper brake

 

Model E4N-ID 

Date: 2013/07/01 

Revision: 1 

www.coremo.it 

 
 

Page 

13

 of 

14

 

 

3.

 

Remove  the  shoe  alignment  spring  C61958  from  its  seat  and  replace  it  with  a  new  one 

positioning it as shown in Figure 3. 

4.

 

Remount the brake shoe following the procedure in point 2 in reverse. 

5.

 

Readjust the play between the disc and the lining as described in Chapter 9.1. 

6.

 

Substitute the safety screw with the silencer. 

 

9.6.

 

Changing the gaskets 

 

 

 

1.

 

Proceed as explained in Chapter 9.4 from point 1 to point 6. 

2.

 

Remove the cover Z50313. 

3.

 

Remove the bell E80822 and springs. 

4.

 

Remove the plate unit  Z50314  and pull out the  internal thruster piston D71224 complete 

with rod D71225. 

5.

 

Using a n. 2.5 Allen key unscrew the screws C61162 and remove the gasket locking flange 

C62219. 

6.

 

Remove  the  damaged  gaskets  (C62216  -  C62218  -  C61841)  and  the  o-ring  (C61820)  and 

replace them with new ones. Before placing the new gaskets in their seats, lubricate with 
mineral  oil.  Grease  the  stem  (D71225)  and  the  internal  thruster  (D71224)  too  before 
remounting the thruster unit. 

7.

 

Remount following the instructions from point 5 to point 3 of Chapter 9.6 in reverse order. 

8.

 

Remount following the instructions in Chapter 4 from point 8 to point 13 in reverse order. 

Содержание E4N-ID















Отзывы:

Похожие инструкции для E4N-ID