Copystar CS 181 Скачать руководство пользователя страница 84

Страница: 84 / 355

2KJ/2KH

1-3-44

U245

Checking messages
Description

Displays a list of messages or graphics on the operation panel.

Purpose

To check the messages or graphics to be displayed.

Method

1. Press the start key.
2. Select the item to be displayed using the cursor up/down keys.
3. Press the start key. The selected item is displayed.

Method to display the messages

1. Change the screen using the cursor up/down keys to display each message one at a time.

Select the language using the cursor left/right keys.

2. To return to the screen for selecting an item, press the stop/clear key.

Method to display the graphics

1. Change the screen using the cursor up/down keys to display each graphic one at a time.

Select the background (black or white) using the cursor left/right keys.

2. To return to the screen for selecting an item, press the stop/clear key.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U246

Setting the finisher
Description

Provides various settings for the built-in finisher, if furnished.

Purpose

Adjusts the side registration cursor stop position if paper registration is poor or stapling is made outside the
specified area.

Setting

1. Press the start key.
2. Select the desired cursor position using the cursor up/down keys.
3. Change the setting using the cursor left/right keys.

4. Press the start key. The value is set.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Check display messages

Check the messages

Check display graphics

Check the graphics

Display

Description

Setting
range

Initial
setting

Change in
value per step

FRONT

Front side registration cursor stop
position

0 to 8

0.566 mm

REAR

Rear side registration cursor stop
position

0 to 8

0.566 mm

END

Trailing edge registration cursor stop
position

0 to 8

0.566 mm

Содержание CS 181




































































































































































































































































































































































Результаты поиска

Содержание CS 181

Отзывы:

Бренды по названию

Популярные бренды

Copystar CS 181, Руководство по обслуживанию

Результаты поиска

Содержание CS 181

Отзывы:

Бренды по названию

Популярные бренды