Copystar CS 181 Скачать руководство пользователя страница 193

Страница: 193 / 355

2KJ/2KH

1-5-41

1-5-4 Drum section

(1) Detaching and refitting the drum unit

Follow the procedure below to replace the drum unit.

Cautions

Avoid direct sunlight or strong light when detaching and refitting the drum unit.
Never touch the drum surface when holding the drum unit.

Procedure

1. Open the front cover and left cover. Remove

the waste toner box and toner container.

2. Remove the screw holding the developing

release lever.

3. Pull the developing release lever and

release the developing unit.

Figure 1-5-70

4. Remove the screw and the connector and

then remove the drum unit.

5. Replace the drum unit and refit all the

removed parts.

6. when the periodic maintenance, perform

maintenance mode U251 (clearing the
maintenance count) (see page 1-3-45).

Figure 1-5-71

Developing release lever

Screw

Drum unit

Connector

Screw

Содержание CS 181




































































































































































































































































































































































Результаты поиска

Содержание CS 181

Отзывы:

Copystar CS 181, Руководство по обслуживанию, Страница: 193 / 355

Результаты поиска

Содержание CS 181

Отзывы: