manualshive.com logo in svg

Copley Controls Accelnet Plus BE2 Series, Руководство пользователя, Страница: 56 / 125

Поделиться
Скачать
Copley Controls Accelnet Plus BE2 Series Скачать руководство пользователя страница 56

Accelnet & Stepnet Plus Panels User Guide 

16-01339 Rev 07

 

4.15  S

TATUS 

I

NDICATORS

 

D

RIVE 

S

TATUS 

I

NDICATOR

 

BEL, BPL, TEL 

BE2, BP2, TE2, TP2 

BML 

 

 

 

 

 

AMP LED 

A bi-color LED gives the state of the BEL drive. Colors do not alternate, and can be solid ON or blinking. When 
multiple conditions occur, only the top-most condition will be displayed. 
When that condition has been cleared the next one below will shown.  

Red/Blinking 

= 

Latching fault.  Operation will not resume until drive is Reset. 

Red/Solid 

= 

Transient fault condition. Drive will resume operation when 

 

 

the condition causing the fault is removed. 

Green/Double-Blinking 

= 

STO circuit active, drive outputs are Safe-Torque-Off 

Green/Slow-Blinking 

= 

Drive OK but NOT-enabled.  Will run when enabled. 

Green/Fast-Blinking 

= 

Positive or Negative limit switch active.  

 

 

Drive will only move in direction not inhibited by limit switch. 

Green/Solid 

= 

Drive OK and enabled.  

 

 

Will run in response to reference inputs or EtherCAT commands. 

Off 

= 

No HV or HVAUX power to drive 

Latching Faults

 

Defaults 

Optional (programmable) 

•  Short circuit (Internal or external) 

•  Over-voltage 

•  Drive over-temperature 

•  Under-voltage 

•  Motor over-temperature 

•  Motor Phasing Error 

•  Feedback Error 

•  Command Input Fault 

•  Following Error 

•  Motor Wiring Disconnected 

 

 

•  Over-current (Latched, I

2

T) 

 

 

Содержание Accelnet Plus BE2 Series






























































































































Отзывы:

Нет отзывов