Copley Controls Accelnet Plus BE2 Series страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 125

background image

Accelnet & Stepnet Plus Panels User Guide

16-01339 Rev 07

F

AULT

D

ESCRIPTIONS

The set of possible faults is described below. For details on limits and ranges, see Fault Levels (4.17).

Fault Description

Fault Occurs When…

Fault is Corrected When…

* Short Circuit
Detected

Output to output, output to ground, internal PWM bridge
fault.

Short circuit has been removed.

* Amp Over
Temperature

Drive

’s internal temperature exceeds specified

temperature.

Drive temperature falls below specified
temperature.

* Motor Over
Temperature

Motor over-temperature switch changes state to indicate
an over-temperature condition.

Temperature switch changes back to
normal operating state.

Over Voltage

Bus voltage exceeds specified voltage limit.

+ DC bus voltage returns to specified
voltage range.

Under Voltage

Bus voltage falls below specified voltage limit.

+ DC bus voltage returns to specified
voltage range.

* Feedback error

Over current condition detected on the output of the
in5 Vdc supply used to power the feedback.
Resolver or analog encoder not connected or levels out of
tolerance.

Encoder power returns to specified
voltage range. Feedback signals stay
within specified levels.

Motor Phasing
Error

Encoder-based phase angle does not agree with Hall
switch states. This fault can occur only with brushless
motors set up using sinusoidal commutation. It does not
occur with resolver feedback or with Halls correction
turned off.

Encoder-based phase angle agrees
with Hall switch states.

* Following Error

User set following error threshold exceeded.

See
Position and Velocity Errors (3.13).

Command Input
Fault

Loss of PWM input, or network command data

PWM signals restored, network
communications resume

Motor Wiring
Disconnected

Used with motor brakes, a programmable time during
which current-flow in the motor will be tested before the
brake is released. If current is not detected, it is a fault.

Motor current is detected during
programmable delay before brake is
released.

Over Current
(Latched)

Optional: The

I

2

T

current-limit for the drive has been

reached

Reduce drive current

* Configured as

latching

by default. Programmable to be

non-latching

.

«
...
36
37
38
39
40
...
»

Содержание Accelnet Plus BE2 Series






























































































































Отзывы:

Нет отзывов

Похожие инструкции для Accelnet Plus BE2 Series

Бренд: National Instruments Страницы: 29

Бренд: Parker Страницы: 103

Бренд: Lenze Страницы: 8

Бренд: Becker Страницы: 16

Бренд: Becker Страницы: 28

Бренд: Lenovo Страницы: 68

GREENSMASTER 3100

Бренд: Toro Страницы: 48

Greensmaster 3150

Бренд: Toro Страницы: 48

Бренд: BenQ Страницы: 2

Бренд: Robotis Страницы: 22

Reliance electric SP600 Series

Бренд: Rockwell Automation Страницы: 4

Reliance Electric SP200

Бренд: Rockwell Automation Страницы: 60

Allen-Bradley Kinetix 5100

Бренд: Rockwell Automation Страницы: 90

Бренд: Rockwell Automation Страницы: 136

Бренд: Sanyo Denki Страницы: 138

Бренд: FujiFilm Страницы: 547

Бренд: FALK Страницы: 8

Бренд: Saftronics Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды