C A T A L O G # :
T Y P E :
Specification grade, wet listed 71 watt
MR16 lamp adjustable fixture.
Adjustment mechanism features hot
aiming capability, aiming marks and too-
less locking. Optics provide glare-free
50° cutoff to lamp and lamp image. For
use with all halogen MR16 lamp vari-
eties. Units small size is ideal for tight
construction areas. Insulation must be
kept 3" away from sides and top of fix-
ture. Optical element can be changed
after installation to provide a variety of
distributions. e.g. into a Downlight
. . .
Re f l e c t o r
.040 thick aluminum spun parabolic interior
reflector in Clear, Gold, Haze, Warm Haze, Black
Alzak® finish
.
Special cone colors listed below.
. . .
G l a s s
.125 thick tempered clear glass protects lamp
from direct spray of water and is retained during
relamping.
. . .
F l a n g e
Self flange reflector or die-cast flange with either
matte white or clear coat finishDie-cast flanges
are easily removed for field painting. Elements are
keyed for proper insertion.
. . .
A d j u s t a b i l i t y
Removable lamp adjustment mechanism provides
up to 45° tilt and 361° rotation and locks into any
aiming position. Unit is relamped without unlocking
adjustments. Translating centerbeam optics maxi-
mize light output.
. . .
L e n s
Soft focus lens standard for smooth beam
patterns. Up to two filter media can be used
which are retained during relamping.
. . .
A t t a c h m e n t
Positive torsion springs pull flange tight to ceiling.
Mechanical light trap eliminates spill light at edge
of flange or reflector.
. . .
So c k e t
GX5.3 base for Bi-pin MR16 lamps. Back light
shield keeps interior of fixture dark.
. . .
T r a n s f o r m e r
Truvolt
™
toroidal transformer with dual-output taps
for proper 12.0V operation and quiet operation
when dimmed. Dimmer tap compensates for inher-
ent voltage loss from dimmers, resulting in 30%
more lumens than traditional laminated transform-
ers. Toroidal design, with 90% or greater efficien-
cy, features a rolled one-piece continuous core of
M3 grade grain oriented silicon steel complete with
an integral thermal to protect against overheating.
For dimming, use dimmers rated for electromagnet-
ic transformers. Transformer is warranted for 5
years and is serviceable from below ceiling.
Note: If a dimming system is operated for con-
struction lighting in its "shunt" mode, i.e. bypass-
ing the dimmer modules, for an extended period of
time, fixtures with the dual-tap toroidal transformer
should be operated on the "Switched Fixture" out-
put until the dimmers are in use. Operating fixtures
on the "Dimmed Fixture" output with a full 120v
input for an extended period will overdrive the
lamp and cause shortened lamp life.
. . .
F r a m e / H o u s i n g
Hot dipped galvanized 20 gauge steel frame
with built in 1/2 inch plaster lip. Gunsights allow
for consistent alignment.
. . .
J u n c t i o n B o x
18 cubic inches, listed for 4#12 AWG or 6#14
AWG 90° C additional feed through conductors,
has three 1/2" pryouts.
. . .
B a r H a n g e r s
No Flex
®
bar hangers with positive locking, for
use with wood, engineered wood and steel frame
joists spaced up to 24" O.C. ship with platform.
For use in T-bar ceilings order accessory push on
clips. Nailess barb and locator lip provide consis-
tent installation height.
. . .
C o d e s
Thermally protected, IP labeled. Unit is airtight and
exchanges less than 2.0 CFM with the plenum at a
pressure of 75 pascals. Insulation must be kept
three inches away from fixture sides and none on
top as to entrap heat.
. . .
L a b e l s
3 " A D J U S T A B L E
S H O W E R
3 1/2"
[89mm]
4 3/8"
[112mm]
5 1/8"
[130mm]
5"
[127mm]
8 5/8"
[220mm]
4 3/8"
[112mm]
11 7/8"
[302mm]
E N E R G Y D A T A
120V Input
Lamp
Input Operating
Watts
Watts
Current
20
23
.19
35
41
.34
37
42
.35
42
47
.39
50
57
.48
65
70
.58
71
77
.64
75
81
.68
Note: O.D. on SF
is 4 7/8"
Ceiling Cutout:
4 3/8" [112mm]
ADI042551
S A M P L E N U M B E R : P N 3 M R - E 3 A A S R C
Complete unit consists of a platform and element
PN3MR = 3" Non-
IC Low Voltage
Housing
PN3MR REMOTE =
3" Non-IC Housing
for Remote
Transformer
P l a t f o r m
A c c e s s o r i e s
MBCLP = 40
Push On T Bar
Clips (for 10
Units)
PLE3 = Plaster
Lip Extension
for Max 2"
Thick Ceiling
L-SPD =
Spread Lens
L-LNR = Linear
E3AASR
= 3"
MR16
0 - 45°
Adjustable
Accent
Lensed
Reflector
O p t i c a l
E l e m e n t
Blank= White
die-cast
SF= Self
Flange
SFWF= Self
Flange Painted
White
RAW= Natural
Die Cast
F l a n g e
F i n i s h
Standard
C=Clear
H=Haze
G=Gold
WMH=Warm
Haze
W=Gloss White
B= Black
MW= Matte
White
Custom
K=Cognac
KH=Cognac
Haze
CC=Chocolate
Custom
CCH=Chocolate
Haze
BU=Blush
Custom Cont.
BUH=Blush
Haze
GP=Graphite
GPH=Graphite
Haze
PN=Pine
PNH=Pine Haze
SK=Sky
SKH=Sky Haze
Spread Lens
L-UV = UV
Reduction Lens
L-LPINK =
Light Pink
L-LSTRAW =
Light Straw
Lens
L-27K =
2700K dichroic
filter
L-DAY =
Daylight Lens
L-SPINK =
Surprise Pink
Lens
L-PLAV = Pale
Lavender Lens
L-HEX= Hex
Cell Louver
For additional options please consult factory.
Matte white is recommended for self flanged reflectors
