Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 93

Страница: 93 / 93

Shenzhen Coolmay Technology Co.,Ltd

CX-WIFI-2NET module user manual

www.coolmay.com

Page

, Total 93 pages

Question 8: Does the WIFI module TCP support UDP multicast?

At present, all WIFI modules do not support UDP multicast. The IP

multicast address range is 224.0.0.0~239.255.255.255. Do not set the
above IP segment when setting the module. If it is set, the module may
not start properly.

Question 9: The WIFI module works in STA mode. How does the

host computer obtain the IP of the module?

All wifi modules support UDP search, and will return their own IP,

MAC, and MID accordingly. The specific search process is as follows:

1. Send a password via UDP broadcast (broadcast address:

xx.xx.xx.255,

port:

48899).

The

default

password

is:

"HF-A11ASSISTHREAD". This password can be set with AT command
(AT+FASWD), up to 100. byte.

2. After the module receives the password, if the password is correct,

send the local IP address to the address (unicast, port: 48899) and

MAC address and module name. (IP, MAC, MID such as

10.10.100.254, 888B5D0000E2, guxin).

In this way, the host computer APP can obtain the IP address of the

module.

Содержание CX-WIFI-2NET






























































































Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Бренды по названию

Популярные бренды

Coolmay CX-WIFI-2NET, Руководство пользователя

Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Бренды по названию

Популярные бренды