manualshive.com logo in svg

Coolmay CX-WIFI-2NET, Руководство пользователя

Поделиться
Скачать
Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 57

Shenzhen Coolmay Technology Co.,Ltd 

                                                       

CX-WIFI-2NET module user manual           

      

 

 

Page 

57

 , Total 93 pages 

www.coolmay.com 

3.2.2.2.31 AT+MMID   

  Function: Set module ID command 

  Format: 

   AT+MMID=<ID><CR> 

   +ok=<ID><CR>< LF ><CR>< LF > 

parameter: 

     ID: The value of the ID, ranging from 0 to 65535. 

 

3.2.2.2.32 AT+IDFIR   

Function: First built with ID function to turn off the command format: 

    AT+IDFIR=on/off<CR> 

    +ok<CR>< LF ><CR>< LF > 

This command enables or disables the first built-in ID function. The default is off. 

 

3.2.2.2.33 AT+IDEVE   

Function: Each data with ID function turns on the off command format: 

    AT+IDEVE=on/off<CR> 

    +ok<CR>< LF ><CR>< LF > 

This command enables or disables the data ID function each time. The default is off. 

Note: The function of the ID requires the server to handle it accordingly. When the 

module is connected to the server, it will have a two-byte ID number in front of the 

data (ID range is 0~65535, high byte first, low byte later) plus two bytes of ID inverse. 

For example, if the default ID of the module is 1111, the first four bytes are sent to 

the server as "0x04 0x57 0xFB 0xA8". 

 

3.2.2.2.34 AT+AABR 

Function: adaptive baud rate function on and off command 

Format: 

Содержание CX-WIFI-2NET






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды