manualshive.com logo in svg

Coolmay CX-WIFI-2NET, Руководство пользователя

Поделиться
Скачать
Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 17

                                                       

CX-WIFI-2NET module user manual           

      

 

Shenzhen Coolmay Technology Co.,Ltd                                                                                                       

www.coolmay.com

 

Page 

17

 ,Total 93 Pages 

☆

  The  module  can  be  easily  set  by  the  AP+STA  function,  which  solves  the 

problem that the previous module can only be set through the serial port when it is in 
the STA. 

  

AP+STA Function setting: 

The  AP+STA  function  needs  to  be  set  through  the  serial  port  command 

(F-logarithmic setting). 

AT+FAPSTA=on Sets the AP+STA function (the factory settings are in effect). 
Then when the module is set to STA mode, the AP interface is still valid. 

Note on AT+STA mode: 

When  the  AP+STA  function  is  enabled,  the  STA  port  needs  to  be  connected  to 

other routers. Otherwise, the STA port will continuously scan the router. When scanning, 
it will affect the AP port, such as data loss. 

If the user determines that the STA cannot connect to the AP at this time, you can 

use the command to stop scanning the STA port. 

AT+STTC=on/off,  on  means  scanning  the  router,  off  is  not  scanning,  and  the 

command is not saved after restarting. 

AT+FSTTC=on/off,  this  command  can  be  saved,  and  the  original  settings  will  be 

maintained after restarting. 

 

2.4 Ethernet interface networking mode 

 

The  CX-WIFI-2NET  module  provides  a  100M  Ethernet  interface.  Through  this 

100M Ethernet interface, users can implement WIFI port, serial port, Ethernet port, and 
three  interfaces  to  communicate  with  each  other.  In  terms  of  networking,  the 
CX-WIFI-2NET  module  supports  bridging  mode,  routing  mode  and  switch  mode  to 
correspond to different specific applications. 

<Description>: 
The Ethernet function has two network ports. The second network port can be used 

as either a LAN port or a WAN port. The first network port can only be used as a LAN. 
The bridge mode described below uses only the network port 2. The route mode can 
use either network port 1 or network port 2. The switch mode uses two network ports at 
the same time. 

For  different  networking  modes,  the  CX-WIFI-2NET  module  needs  to  be 

version-switched through commands. Use the command AT+FVER=n to switch to the 
(2.4.2) routing mode, and AT+FVER=z to switch to the (2.4.3) bridge mode. 

 

2.4.1 CX-WIFI-2NET module Ethernet interface function (AP) 

 

Содержание CX-WIFI-2NET






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды