manualshive.com logo in svg

CoolAutomation SMT-131, Руководство пользователя, Страница: 15 / 18

Поделиться
Скачать
CoolAutomation SMT-131 Скачать руководство пользователя страница 15

 
Page 15 
 

Option List Table 

 

 

Option 

Setting 

0 

Buttons Shown 

0: Both mode and fan buttons show (default) 
1: Show mode but fan button hidden 
2: Show fan but mode button hidden 
3: Both mode and fan buttons Hidden 
Note:  If  the  mode  button  is  hidden,  the  service  and 
maintenance staff can turn the SMT-131 on or off by pressing 
and holding the lower left of the LCD for 15 seconds. 2 chirps 
indicate  the  SMT-131  has  turned  ON.  1  chirp  indicates  the 
SMT-131 has turned off (ver 3.03+) 

1 

Permitted Modes 

0: Off / Auto 
1: Off / Auto / Heat / Cool  
2: Off / Heat /Cool 
3: Off / Heat 
4 Off / Cool 
5: Off / Auto (Display current heating or cooling mode) 

2 

Room / Set display 

0: Show room and set temp (default) 
1: Show set temp only 

3 

Native display format 

0: C (default)  
1: F 

4 

C/F button shown on LCD 

0: Off(default)  
1: On 

5 

High temp set limit 

5C-30C or 41F-86F  

6 

Low temp set limit 

5C-30C or 41F-86F  

7 

Dead band 

0C-5.0C or 0F-10.0F in 0.1C/0.1F steps.   
Depending on Option 3 above. 
Data format: Dead band * 10 

8 

Fan Purge Period 

0: OFF 
1: Fan purge - 1 min 
2: Fan purge - 3 min 
3: Fan purge - 5 min 
4: Fan purge - 10 min 
5: Heat only fan purge - 1 min 
6: Heat only fan purge - 3 min 
7: Heat only fan purge - 5 min 
8: Heat only fan purge - 10 min 
9: Cool only fan purge - 1 min 
10: Cool only fan purge - 3 min 
11: Cool only fan purge - 5 min 
12: Cool only fan purge - 10 min 

9 

Fan span  
 

0.5C-3.0C/1.0F-6.0F 0.1C/0.1F steps 
Data format: Fan span * 10 

10 

0-10V Fan Interval   (PI) 

10-300 seconds 10 seconds' steps (60 seconds default) 

11 

0-10V Fan direction 

0: 0 - 10V 

–

 slow to fast (Forward Acting) 

1: 10 to 0V 

–

 slow to fast (Reverse Acting) 

12 

0-10V Fan minimum value 
(Starting  fan  voltage  when 
running) 

0 -10V 
Data format: 0-10V Fan minimum value * 10 

 

 

Содержание SMT-131



















Отзывы:

Нет отзывов