CoolAutomation CoolMasterNet Скачать руководство пользователя страница 46

Страница: 46 / 47

ASCII I/F

CoolMasterNet PRM Rev 0.7

www.coolautomation.com

EXAMPLE

Query centralize address of Indoor Units on line L2 (SA/TO/PN)

CA L2 ?

L2.101 --> Z56
L2.102 --> Z62
L2.103 --> Z23
L2.104 --> Z33
OK

Distribute new group addresses on line L1 starting from 300 (DK)

CA L1 300

OK, Boot Required!

SYNOPSIS

va
va auto
va delall
va ram R
va - <

va + <

DESCRIPTION

In order to simplify translation of the

UID

into ModBus object address, CoolMasterNet uses VA (Virtual

Address), associated with

UID

. Each

UID

can have none, one or a number of associated VA's, but each VA can

be associated only with one

UID

. VA's are plain numbers starting from 001 (decimal). Virtual Address concept is

applicable to

CoolGate 5

and

ModBus IP

In format without parameters va command will list all VA associations and their ModBus addresses in
hexadecimal and decimal format.

va auto - CoolMasterNet will automatically associate VA's with existing (visible with

command)

UID

's.

This will delete previous associations

va delall - delete all VA associations

va ram R - create VA Data Base for R associations. The operation will take effect after reboot. Use this
operation only if default VA Data Base is too small.

va - <

UID_STRICT

|VA> - delete all VA associations with specific Indoor Unit or delete specific VA

association

va + <

UID_STRICT

> <VA> - add new VA association

EXAMPLE

Auto associate all existing Indoor Units

va auto

Associate VA 007 with Indoor Unit 100 on line L1

va + L1.100 7

List all VA associations

Содержание CoolMasterNet
















































Результаты поиска

Содержание CoolMasterNet

Отзывы:

CoolAutomation CoolMasterNet, Руководство пользователя, Страница: 46 / 47

Результаты поиска

Содержание CoolMasterNet

Отзывы: