CoolAutomation CoolMasterNet Скачать руководство пользователя страница 43

Страница: 43 / 47

ASCII I/F

CoolMasterNet PRM Rev 0.7

www.coolautomation.com

L1.300 -
L1.301 +
L1.302 -
L2.100 ?
L2.101 ?
L2.102 ?
L2.103 ?
OK

Unset main RC: Indoor Unit 206 on line L2

main L2.206 0

Set new main RC: Indoor Unit 201 on line L2

main L2.201 1

vam

SYNOPSIS

vam <

UID_STRICT

> <a|b|x|n|l|L|h|H|s|t|A|+|->

vam
vam <

UID_STRICT

DESCRIPTION

Control Ventilation Unit.

vam

<UID_STRICT>

- get Ventilation Unit status.

vam - get all Ventilation Units status.

Letter

Operation

Compatibility

Auto Mode

Bypass (Bps) Mode

Heat Exchange (HExc) Mode

Normal Mode

Sleep Mode

Low Fan

Low Fan with Fresh-Up

High Fan

High Fan with Fresh-Up

Super High Fan

Top Fan

Auto Fan

Turn on ventilation unit*

Turn off ventilation unit*

ON/OFF control of the Ventilation Unit is performed with regular

and

o f f

commands.

There are, though, dual units, that consist of Air Condition Unit and Ventilation unit. In this case

and

o f f

commands will control the Air Condition Unit, while vam <

UID_STRICT

> +/vam <

UID_STRICT

> - will

control the Ventilation Unit.

EXAMPLE

Set Heat Exchange mode on Ventilation Unit 101 on Line L1

vam L1.101 x

Содержание CoolMasterNet
















































Результаты поиска

Содержание CoolMasterNet

Отзывы:

CoolAutomation CoolMasterNet, Руководство пользователя, Страница: 43 / 47

Результаты поиска

Содержание CoolMasterNet

Отзывы: