CoolAutomation CoolMasterNet Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 47

CoolAutomation CoolMasterNet Скачать руководство пользователя страница 26

ASCII I/F

CoolMasterNet PRM Rev 0.7

26

www.coolautomation.com

© 2017 CoolAutomation

L1.102 | - | 0 | c d f h a | l m h a |
L2.107 | - | 1 | c d f h a | l h |
L1.101 | - | 1 | c f hx | l m h a |
OK

link

SYNOPSIS

l i n k
link delall
link -L
link ram R
link <

UID1_STRICT

UID2_STRICT

>

DESCRIPTION

Control link operation in CoolMasterNet. Linking ThermoPad on

line with Indoor Unit will grant the

ThermoPad full control over the Unit.

·

In format without parameters l i n k will list existing links

·

link delall - delete all links

·

link -L - delete link number L (link numbers displayed in the list of existing links)

·

link ram R - create link Data Base for R groups. The operation will take effect after reboot. Use this
operation only if default link Data Base is too small.

·

link <

UID1_STRICT

UID2_STRICT

> - create new link, where UID1 is ThermoPad on

line and UID2 is Indoor Unit. The command generate invisible

for one of the UID's. <=|~> defines link

type: = regular link, the ThermoPad will become invisible; ~ link with haux mode usage, the Indoor Unit will
become invisible. Regular link will allow to control the Indoor Unit through UID2, while haux link through UID1.

EXAMPLE

List existing links

>

link L3.082=L1.101

L000: L3.081 <--> L7.096
L001: L3.083 <--> L1.100
OK

Delete link number 0

>

link -0

OK

Link ThermoPad 082 on line L3 with Indoor Unit 101 on line L1 (regular link)

>

link L3.082=L1.101

OK, Boot Required!

Link ThermoPad 080 on line L3 with Indoor Unit 100 on line L1 (haux link)

>

link L3.080~L1.100

OK, Boot Required!

Delete all links

>

link delall

OK

Create link Data Base for 60 links

>

link ram 60

OK, Boot Required!

plug

SYNOPSIS

plug <

> <ascii if command>

«
...
24
25
26
27
28
...
»

Содержание CoolMasterNet
















































Отзывы:

Нет отзывов