CoolAutomation CoolMasterNet Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 47

CoolAutomation CoolMasterNet Скачать руководство пользователя страница 22

ASCII I/F

CoolMasterNet PRM Rev 0.7

22

www.coolautomation.com

© 2017 CoolAutomation

Netmask

R/W

string

Set Netmask address in case IP is static

Gateway

R/W

string

Set Gateway address in case IP is static

DNS1

R/W

string

Set prefered DNS address

DNS2

R/W

string

Set alternate DNS address

EXAMPLE
Query

>

ifconfig

MAC : 28:3B:96:00:02:0F
Link : Up
IP : 192.168.16.108 (DHCP)
Netmask: 255.255.255.0
Gateway: 192.168.16.254
DNS1 : 8.8.8.8
DNS2 : 8.8.4.4
OK

Configure fixed IP, Gateway and Netmask

>

ifconfig IP 192.168.1.102

OK, Boot Required!
>

ifconfig Gateway 192.168.1.0

OK, Boot Required!

>

ifconfig Netmask 255.255.0.0

OK, Boot Required!

Configure DHCP client operation

>

ifconfig IP DHCP

OK, Boot Required!

Disable Ethernet

>

ifconfig disable

OK, Boot Required!

Change DNS prefered address

>

ifconfig DN1 208.67.222.222

OK, Boot Required!

boot

SYNOPSIS

boot
boot [N]

DESCRIPTION

·

<N> omitted - Enter Boot Mode

·

<N> = 2 - Reset CoolMasterNet

sddp

SYNOPSIS

sddp
sddp <enable|disable|identify|offline|alive>

DESCRIPTION

Configure Control4® Simple Device Discovery Protocol (SDDP) module. CoolMasterNet is compliant with
Control4® SDDP v1.0 specification and can act as SDDP enabled device.

«
...
20
21
22
23
24
...
»

Содержание CoolMasterNet
















































Отзывы:

Нет отзывов