Coolair MNBCDD36J Скачать руководство пользователя

Страница: 1 / 12

MNBCDD36 & MNEFDD36

GALVANIZED WALL FANS

Installation, Operation, and Maintenance Instructions

FARM PRODUCTS DIVISION

MEMBER OF AMCA

AMERICAN COOLAIR CORPORATION

P.O. BOX 2300

JACKSONVILLE, FLORIDA 32203

PHONE (904) 389-3646 FAX (904) 387-3449

E-MAIL - [email protected]

MNBCDD36J * MNBCDD36K * MNEFDD36J * MNEFDD36K

MNBCDD36J-RM * MNBCDD36K-RM

MNEFDD36J-RM * MNEFDD36K-RM

UNPACKING

Inspect the fan for signs of shipping damage. It is the responsibility of the customer to report any
shipping damage to the freight carrier.

WHAT SHOULD YOU FIND?

Fan, (4) Housing Sheets, Damper Door Assembly, Cone (4 cone panels and 4 cone gussets), Rear Housing Guard,
Front Cone Guard, and Hardware Package

Figure 1

48 1/2

14 3/8

48 1/2

Fan

DD36

DD36-RM

Dimensions
in inches

Содержание MNBCDD36J













Результаты поиска

Содержание MNBCDD36J

Отзывы:

Похожие инструкции для MNBCDD36J

Бренды по названию

Популярные бренды

Coolair MNBCDD36J, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MNBCDD36J

Отзывы:

Похожие инструкции для MNBCDD36J

Бренды по названию

Популярные бренды