COOL BOSS CB-12SL Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

COOL BOSS CB-12SL Скачать руководство пользователя страница 22

Cool Boss Evaporative Air Cooler

22

P/N 5900274 — August 2022 — Rev. A1

Operation

This section describes how to operate your Cool Boss Evaporative Cooler.

⚠

WARNING

The Cool Boss should only be operated by authorized, trained personnel. That
training includes reviewing and understanding the Operation Manual and Safety

Labels on the Cool Boss. Do

not

allow children or impaired persons to operate the

Cool Boss.

⚠

WARNING

Never roll anything heavy or sharp over the power cord.

Try to find a

location where people will not be constantly walking over the power cord,

presenting a tripping hazard. The product should only be operated by authorized,
trained personnel.

⚠

WARNING

Never operate the Cool Boss unless the Ground Fault Circuit Interrupter (GFCI) is
functioning.

⚠

WARNING

Never

remove the Ground Prong from the plug end of the Power Cord. Do not

operate the unit if the power cord is damaged.

⚠

WARNING

Do

not

run the Power Cord under a rug or other flammable material.

⚠

WARNING

Use only in a well ventilated open environment with a fresh air supply.

⚠

WARNING

The Cool Boss area must be free from airborne pollutants, flammable gases and
contaminates.

⚠

WARNING

Ambient operating temperature must remain b65˚ to +113˚F / +18˚ to
+45˚C

⚠

WARNING

Never spray the Cooler with water as the Cooler is not sealed and moisture may
harm the motor or other electrical system components.

⚠

WARNING

Do

not

operate near open containers of flammable liquids or gases.

⚠

WARNING

Always maintain a minimum distance of 50 feet / 15 meters from any open flame or
sparks.

⚠

WARNING

The Cool Boss is not designed to be used by children or persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge unless

they have been given supervision or instruction concerning use by a person

responsible for their safety.

⚠

WARNING

Never operate the Cool Boss unless all Media is securely in place.

⚠

WARNING

Always dry the Media after use by turning off the Water Supply to the Media and
running the Fan without circulating water. This may take from 15 to 45 minutes

depending on temperature and humidity.

«
...
20
21
22
23
24
...
»

Содержание CB-12SL





































Отзывы:

Нет отзывов