Tighten the cams as you go (refer to
cam fitting and locking section above).
Then carefully slide panel into the
grooves.
Fit panels to panel .
Then fit panel to panel , referring
to the End Panel detail above for the
correct fitting position
A
A
A
A
B
B
C
B
C
C
B
C
A
A
A
A
A
A
A
A
B
B
C
B
C
B
C
B
C
C
B
C
B
C
B
C
Insert into panels and as shown.
Then insert and into panels as shown.
1 x Fixed Shelf
2
x Shelf
2 x Back Panel
Installation should be performed by a competent person
only. This product could be dangerous if incorrectly installed.
Check the pack to ensure all of the components are included.
When you are ready to start, make sure that you have all of
the correct tools to hand, have plenty of space, and that the
area for building is clean and dry.
Do not rush! Read these instructions first and run through
the sequence before you begin. Assembly should be
carried out in the steps shown in the following diagrams,
constructing one unit at a time and keeping fittings together
to avoid loss. Lay large panels on the floor using the
packaging for protection. Do not overtighten screws, as this
may damage the cabinet.
If any items are missing, or problems arise with fitting,
please call the
Manufacturers’ Helpline on 01769 575500
.
To clean - use mild soap and water only.
Do not use abrasive cleaners.
*** IMPORTANT INFORMATION ***
BEFORE YOU START
12
3
9
6
12
3
9
6
12
3
9
6
12
2
3
9
6
Turn to 2 o’clock to lock.
12
3
9
6
12
3
9
6
12
3
9
6
12
2
3
9
6
IMPORTANT:
CAM FITTING AND LOCKING:
Press in firmly.
A
12
3
9
6
12
3
9
6
12
3
9
6
12
2
3
9
6
Leave no gaps.
12
3
9
6
12
3
9
6
12
3
9
6
12
2
3
9
6
Turn clockwise.
A
12
3
9
6
12
3
9
6
12
3
9
6
12
2
3
9
6
Fully insert .
B
12
3
9
6
12
3
9
6
12
3
9
6
12
2
3
9
6
Attach the LH wall hanging bracket and RH wall
hanging bracket to both panels , in the pre-marked
positions, using screws .
Please use scissors to open the bag of fittings and then empty
the contents into a bowl, so that they do not get lost!
1 x LH End Panel
1 x RH End Panel
2 x Top & Base Panel
A
B
C
A
B
C
F
J
M
N
P
12 x
12 x
12 x
2 x
8 x
1 x
1 x
2 x
HARDWARE:
WALL FIXINGS:
PANELS:
CROSS HEAD SCREWDRIVER
HAMMER
SPIRIT LEVEL
MINIMUM TOOLS REQUIRED:
DRILL & DRILL BITS (3mm & 5mm)
3
5
STEP 1:
STEP 2:
ASSEMBLY GUIDE
CSS 1618
07/15
STANDARD & TALL DRESSER WALL CABINETS
15mm
15mm
15mm
25mm
30mm
50mm
50mm
15mm
15mm
15mm
25mm
30mm
50mm
50mm
15mm
15mm
15mm
25mm
30mm
50mm
50mm
15mm
15mm
15mm
25mm
30mm
50mm
50mm
15mm
15mm
15mm
25mm
30mm
50mm
50mm
E
4 x
15mm
15mm
15mm
25mm
30mm
50mm
50mm
A
A
A
A
A
B
B
C
C
C
B
B
C
C
C
A
A
A
A
B
B
B
B
A
A
A
B
C
B
C
A
IMPORTANT:
When fitting
Arrow points to
outside edge.
M
N
E
E
E
E
E
M
N
1
1
3
3
3
1
1
1
1
1
2
2
3
3
3
4
4
5
5
5
6
6
3
3
3
4
4
Fixed shelf position:
Framed Unit
Non-framed Unit
1
4
6
6
4
1
