manualshive.com logo in svg

Control Techniques Unidrive 1 Series, Руководство пользователя

Поделиться
Скачать
Control Techniques Unidrive 1 Series Скачать руководство пользователя страница 28

Safety 

Information

Product 

Information

Mechanical 

Installation

Electrical 

Installation

Getting 
Started

Menu 0

Running 

the motor

Optimisation

Macros

Advanced 

Parameters

Technical 

Data

Diagnostics

UL Listing 

Information

28

Unidrive User Guide

www.controltechniques.com                                                       Issue Number: 9

3.9      Baffle plates

When a Unidrive size 1 to 4 is through-panel mounted, the fitting of a 
baffle plate causes the heatsink to act as a chimney; this enhances the 
air flow along the heatsink fins to aid cooling (this naturally occurs when 
the drive is surface mounted).
You may make a baffle plate from any suitable conducting or non-
conducting material and attach it to the heatsink by the method 
described as follows.

Figure 3-19 Dimensions for the fabrication of baffle plates for 

model sizes 1 and 2

Attaching a fabricated baffle plate to the heatsink

Table 3-2 Methods of attaching the baffle plate

Figure 3-20 Dimensions for the fabrication of baffle plates for 

model sizes 3 and 4

3.10      Ambient temperature 

The maximum ambient temperature under which the drive can operate 
without derating is 40°C.
Derating can be applied to allow operation up to 50°C ambient 
temperature. 
Please see section 11.1.1

Power and current ratings

on page 190 if 

derating is required.

Model size 

Method of attachment

1 
2

Use the surface mounting brackets.

3
4

Use M6 x 12mm max (or equivalent) thread-forming screws to 

screw into the holes in the heatsink, or tap the holes to a suitable 

thread size.

3.228in

6.929in

1.614in

0.512in

1.535in

13.563in

14.449in

0.256in

2.146in

1.969

in

18.622in

17.236in

0.693in

7.154in

6.949in

4.724in

3.425in

22.047in

23.150in

3.780in

13.780in

3.583in

5.118in

0.276in

4.016in

7.697in

9.606in

189.5mm

7.461in

76mm

2.992in

Содержание Unidrive 1 Series

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды