manualshive.com logo in svg

Contrec 515 FA01, Руководство по эксплуатации

Поделиться
Скачать
Contrec 515 FA01 Скачать руководство пользователя страница 38

Operation

 28

515 FA01 - 29 August 2021

Model Information

The model information items display the hardware, software and application 
versions of the instrument. This information is mainly for service personnel.

Press 

 at any time to exit from the Model information.

Description

2-1--S-

 515  MODEL

The hardware model code. Refer to 

Product Codes

 on 

page 79 for more information.

 FF--FF

 FA01  INPUT

The Application number and the assignment of the inputs. 
Refer to 

Application Information Code

 on page 80 for 

more information.

3_0_000 

500-PM  VERS

The version of 500-Series Program Manager from which 
the application software was compiled.

 026357

 CUSTOM VERS

The Customer version code for this installation. Refer to 

Custom Version Codes

 on page 80 for more information.

 123456

 ABC123  S/N

The instrument serial number and unit tag. The serial 
number is on the top line and unit tag is on the bottom left. 
Both items are entered when the instrument application 
software is initially loaded. If the unit tag is not used the 
default tag, 

UNIT

, will be used.

  16-15

EDITED 27/08

        2019

The time and date when the calibration of the instrument 
was last edited. The format of the time and date is the same 
as for the data logs. This example shows 16:15 (4:15pm) 
on the 27th August 2019. This function is available only if 
the instrument has the real time clock option.

CLASS-3

FLASH  V-019

The instrument Class and Flash (bootloader) version.

      5

POWER  CYCLE

The number of power cycles that have occurred since the 
application software was installed.

      1

WDT   RESET

The number of ‘watchdog timer’ (WDT) resets that have 
occurred since the application software was installed. The 
WDT Reset count is only shown if a WDT Reset has 
occurred.

HOLD.RST

CONFIG  PRINT

If the printer protocol is assigned to one of the 
communication ports, the prompt to print the full program 
configuration report will be shown. Hold Reset to start the 
printing of the configuration report. The report will be in 
a similar format to the report generated by the 500 
Program Manager.

DISPLAY

SET

Содержание 515 FA01



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды