manualshive.com logo in svg

Contrec 515 FA01, Руководство по эксплуатации

Поделиться
Скачать
Contrec 515 FA01 Скачать руководство пользователя страница 22

Installation & Maintenance

 12

515 FA01 - 29 August 2021

Terminal Wiring Insulation

Terminals 1-30 are all rated at <35Vdc and wiring with basic insulation is 
adequate. 

Use copper conductors only.

Relay Wiring

Relay terminals are 31-35 or 31-36 depending on the version of option card 
fitted. When controlling circuits operate at mains voltages, or voltages 
>35Vdc, it is necessary to use UL/CSA approved cabling with 
supplementary insulation and a current capacity suitable for the connected 
circuit. Use copper conductors only. The maximum current must be <5A as 
stated in sec 2. 

Where circuits >35Vdc are connected UL/CSA approved cabling with 
supplementary insulation. 0.75mm², 6A current capacity is sufficient.

Mains Power Wiring

Only use UL/CSA approved cabling with supplementary insulation and 
copper conductors. A minimum cable cross section area of 0.75mm² (18 
AWG) is required. However, this must be selected with respect to the 
installed over-current protection device and in accordance with the local 
relevant Electrical Code of Practice as dictated by the Authority Having 
Jurisdiction (AHJ).

The terminal designations (L/N/E) are clearly indicated just above the mains 
input connector on the rear panel of the instrument.

Содержание 515 FA01



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды