Contec DIG-100M1002-PCI Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 73

Contec DIG-100M1002-PCI Скачать руководство пользователя страница 30

3. External Connection

DIG-100M1002-PCI

23

3.

External Connection

This chapter describes the interface connectors on the product and the external I/O circuits.
Check the information available here when connecting an external device.

How to connect the connectors

Connector shape

To connect an external device to this product, plug the cable from the device into the interface
connector (CH0, CH1, CLK, TRG) shown below.

This product has the following interface connectors: the (CH0, CH1 connector) for analog inputs, (CLK
connector) for reference clock and (TRG connector) for external trigger I/O.

* Please refer to chapter 1 for more information on the supported cable and accessories.

Figure 3.1. Interface Connector Shape

* Please refer to chapter 1 for more information on the supported cable and accessories.

Figure 3.2. Examples of Connecting Options

- BNC connector [plug type]

B6252HB-NPP3G-50

[mfd. by AMPHENOL TAIWAN]

or equivalence to it

Interface connector

(CH0, CH1, CLK, TRG)

CH1

CH0

CLK

TRG

012

45

6

AB

CD

EF

8

CN6

CN7

cTEST Series Digitizer

DIG-100M1002-PCI

MADE IN JAPAN

SW1

CH1

CH0

CLK

TRG

CH1
CH0

CLK
TRG

(CH0, CH1, CLK, TRG)

Option

BNC cable

BNC-Bxxx

«
...
28
29
30
31
32
...
»

Содержание DIG-100M1002-PCI










































































Отзывы:

Нет отзывов