Contec CPS-MC341-DS1 -111 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

background image

2 Setup

CPS-MC341-DS1-111 Hardware Manual

17

Cable Connection

Power

Power Cable

Please elect the power cable which is following specifications.

- Cable: Twisted pair cable (In case of using a single wire, please twist the wires of V + and V-)

- Cable Diameter: AWG24-16(0.2mm

2

-1.25mm

2

)

- Cable Length: 3m or less

FG Cable

Please elect the FG cable which is following specifications.

- Cable Diameter: AWG18-16(0.75mm

2

-1.25mm

2

)

Specification of external power supply

This product in a typical Configuration is designed to operate at least 15W power supply. In addition,
the power supply must satisfy the following requirements.

- Build up time time of up to a voltage 12V: within 2ms - 30ms

Recommended power supply is CPS-PWD-15AW12-01(CONTEC).

If the maximum output current of the external power supply can not afford compared with the

maximum current consumption of this product, the abnormal operation by inrush current and the

load variation during start-up and start-up failure by and aging of the external power supply might
be caused.

LAN (LAN A, LAN B)

Please elect the LAN cable which is following specifications.

- Category: Category 5 or more

- Cable Length: 100m or less

CAUTION

«
...
21
22
23
24
25
...
»

Содержание CPS-MC341-DS1 -111













































Отзывы:

Нет отзывов

Похожие инструкции для CPS-MC341-DS1 -111

Бренд: FAAC Страницы: 60

Бренд: IBM Страницы: 72

Бренд: Hama Страницы: 75

Бренд: Onn Страницы: 11

Бренд: ORMA Страницы: 5

Бренд: urmet domus Страницы: 30

Бренд: Rain Bird Страницы: 2

Бренд: Valx Страницы: 28

Бренд: DAPAudio Страницы: 12

Xenta 400 Series

Бренд: TAC Страницы: 48

Бренд: NaanDanJain Страницы: 12

Бренд: D-TACQ Solutions Страницы: 8

Бренд: American Audio Lab Страницы: 31

Бренд: Cobolt Страницы: 5

Бренд: Ferguson Страницы: 13

Бренд: Globalmediapro Страницы: 11

VoiceBridge VBI10 LED

Бренд: WHD Страницы: 4

Бренд: M-E Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды