Contec CONPROSYS M2M Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 103

Contec CONPROSYS M2M Series Скачать руководство пользователя страница 38

—

PLC Communication Settings

—

M2M Gateway PLC Communication Settings

—

38

—

4.

Ethernet Connection with OMRON PLC

The following is a setting example for Ethernet communication with the OMRON PLC CJ series.
See below for the configuration example regarding communication conditions.

1.

PLC Settings

For Ethernet communication, IP address and communication (connection) port for the PLC LAN port
needs to be set.
The following is a setting example with OMRON PLC maintenance tool, "CX Programmer.



Built-in Ethernet Port Setting

1.

On the "CX Programmer", go to [PLC(C)] - [PLC information(E)], then open the [I/O Table Unit

Setting] screen.

M2M Gateway

PLC

OMRON CJ series
IP address : 10.1.1.180
Subnet mask : 255.

０

.

０

.

０

Communication (Connection)
port : 9600
* Ethernet port of the CPU Unit
is used

IP address : 10.1.1.101
Subnet mask : 255.

０

.

０

.

０

Ethernet connection

FINS command

Communication data cord : Binary

Area type

: Data memory (DM)

Data type

: Channel

Access range : 01000 - 01009
Access cycle : 1 sec.

Area type

: Internal auxiliary relay (WR)

Data type

: Bits

Access range : 010.00 - 010.09
Access cycle : 500 ms.

«
...
36
37
38
39
40
...
»

Содержание CONPROSYS M2M Series








































































































Отзывы:

Нет отзывов