Contec CONPROSYS M2M Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 103

Contec CONPROSYS M2M Series Скачать руководство пользователя страница 23

—

PLC Communication Settings

—

M2M Gateway PLC Communication Settings

—

23

—

3.

Device Configuration

Add Device

  From the PLC setting page, click the [Add Device to CPU] to open the Device configuration page in
the bottom.
  To edit an existing device setting, select the specified device display and the "Device" setting
contents can be shown for editing at the bottom of the screen.
  Set each item, then click the [Add], [Change] or the [Delete] button. Setting details are explained in
the table below.

* As for device configuration, several device configurations can be assigned for one CPU
configuration.
* Completing up to the device configuration accomplishes the PLC communication settings.
Save the settings to ROM and reboot the product, and the communication settings will be enabled.

Device Configuration Page

«
...
21
22
23
24
25
...
»

Содержание CONPROSYS M2M Series








































































































Отзывы:

Нет отзывов