Contec CNT24-2GY Скачать руководство пользователя страница 72

Страница: 72 / 73

8. Appendix

CNT24-2(USB)GY

Appendix

Glossary

The glossary contains a brief description of terms used in this manual.

Terms

Explanation

API

[Application Program

Interface]

It is abbreviation for Application Program Interface.

It is the open program interface for OS corresponding to applications, and all

application processing are basically performed through the API. The API

provided by our company can control hardware by calling device driver.

PDF file

It is abbreviation for Portable Document Format.

It is the document format developed in order to display files not depending on

specified platform. It is developed by Adobe CO.

USB

[Universal Serial Bus]

It is abbreviation for Universal Serial Bus. It is not only a specification for the

connection between a PC and a peripheral equipment but also a kind of

terminal. It can connect a wide range of devices and can be plugged/unplugged

with the power being ON (Hot Plug).

USB 2.0

[Universal Serial Bus

2.0]

The latest USB specification that keeps up the low-compatibility with previous

USB and promotes the data transfer speed to 480Mbps (60MB/sec).

Device ID

[Device Identifier]

It is the ID being set when connecting expansion modules and specifying

connection order. It is only for expansion modules. The channel number is

decided by the setting.

Self power

Supplying power by using AC adapter is called Self-Power.

Please make use of AC adapter when using expansion modules.

Device driver

It is software to operate and set peripheral equipment by a PC, and the

peripheral equipment is installed on the PC. It is simply called Driver.

Device manager

It is a Windows tool which can confirm the behavior of the peripheral equipment

installed on a PC, and the state being identified by Windows and so on.

Device name

The name is set by USB driver to specify modules.

It is set in Properties of Device Manager and specified in the course of API

function initialization and so on.

Hardware wizard

It is support program for user without technical knowledge to add peripheral

equipment to a PC. It runs automatically after the device such as USB device

has been connected.

Bus power

Power is supplied by a host when USB cable is being connected without

connecting an AC adapter.

Firmware

It is the software incorporated into a equipment to perform basic control on

hardware.

Properties

Select modules from Device Manager, right-click and select [Properties] dialog

box from pop-up menu to set the device name.

Module ID

About the ID of the module.

Set unique ID value individually for the modules in order to distinguish the

driver when using multiple modules. Use the factory setting(=0) when using

one module.

Содержание CNT24-2GY










































































Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды

Contec CNT24-2GY, Руководство пользователя

Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды