Contec CNT-3204MT-LPE Скачать руководство пользователя страница 46

Страница: 46 / 79

4. Functions

CNT-3204MT-LPE

Functions

This section describes the features of the board.

Each function described here can be easily set and executed by using the bundled API driver library.
For details, refer to HELP after installing API-PAC(W32).

Types and Operations of Pulse Signals

Types of pulse signals

The following types of pulse signals (operation modes) can be set.

2-phase Input, Synchronous Clear, Multiply by 1

2-phase Input, Synchronous Clear, Multiply by 2

2-phase Input, Synchronous Clear, Multiply by 4

2-phase Input, Asynchronous Clear, Multiply by 1

2-phase Input, Asynchronous Clear, Multiply by 2

2-phase Input, Asynchronous Clear, Multiply by 4

Single-phase Input, Asynchronous Clear, Multiply by 1

Single-phase Input, Asynchronous Clear, Multiply by 2

Single-phase Input with Gate Control Attached, Asynchronous Clear, Multiply by 1

Single-phase Input with Gate Control Attached, Asynchronous Clear, Multiply by 2

phase Input

A two-phase pulse input consists of two pulse inputs phase A (advanced signal) and phase B (delayed

signal) with a phase difference of 90

If the Z phase (reference position signal) is used, the two-phase pulse input can clear the count value to

zero

* Count operation for incremental counting in the CW direction. When decremental counting in the CW direction is

set, the board performs decremental counting at the rising edge of the phase-A signal.

* The minimum phase difference between phases-A and B is 25 nsec. Counting is not performed normally if the phase

difference is less than 25 nsec.

Figure 4.1. Example counting during 2-phase input

Phase-A difference of 25 nsec is required.

Phase-A

(Phase-A/UP)

Phase-B

(Phase-B/DOWN)

Phase-Z

(Phase-Z/CLR)

Count value

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды