Contec CNT-3204MT-LPE Скачать руководство пользователя страница 38

Страница: 38 / 79

3. External Connection

CNT-3204MT-LPE

How to Connect the Counter Input Signal

You can connect to a rotary encoder or linear scale with a TTL level output circuit, or to

an open-collector output circuit. The signal must be an LVTTL level input and can be up to 10MHz.

As pull-up resistors are provided on the board, connect the pull-up voltage to the pull-up pins if

connecting to an open collector output circuit/TTL level output circuit. (Please match the pull-up

voltage to the driving voltage on output side IC. If using 3.3V, connect to the VCC pin on the board.)

Not connecting the pull-up voltage may affect the counter input channel left unconnected.

For a two-phase input, connect both phase A and phase B. For a single phase input, connect to either

phase A or phase B. If not using the Z phase, this does not need to be connected.

Remarks

The pull-up pins are PUP1 (pin 32 *1) for the counter input signal and PUP2 (pin 66 *1) for the

control input signal.

PUP1 (pin 32): Pull-up for A, B, and Z phase input signal

(A0, B0, Z0, A1, B1, Z1, A2, B2, Z2, A3, B3, Z3).

PUP2 (pin 66): Pull-up for the control input signals and for the sampling input signals

(DI0, DI1, DI2, DI3, CLKIN, STARTIN, STOPIN).

*1: Connector pin number on the board.

Example Connection for Counter Input Circuit

*1: The pull-up pins are PUP1 for the counter input signal and PUP2 for the control input signal.

Figure 3.5. Connection when it is pull-up by external 5-V power (Counter Input)

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды