Contec CNT-3204MT-LPE Скачать руководство пользователя страница 17

Страница: 17 / 79

2. Setup

CNT-3204MT-LPE

Step 1 Installing the Software

This section describes how to install the Driver libraries.

Before installing the hardware in a PC, install "Driver Library API-PAC(W32)" from the

bundled media or download and install the latest edition of this software from the CONTEC web
site.

Although some user interfaces are different depending on the OS used, the basic procedure is the same.

About the driver to be used

Two counter drivers are available : API-CNT(WDM) and API-CNT(98/PC).

When using this product, use the advanced digital I/O driver "API-CNT(WDM)". The following
information is focused on setting up API-CNT(WDM).

If you intend to use this product in the existing system where API-CNT(98/PC) is used, continue to use

API-CNT(98/PC).
Please note that the API-CNT(98/PC) does not support Windows 8 or later, and the 64-bit OS.

Use the API-CNT(98/PC)

If you are installing from disk attachments, select "all" from the "Installer" later in this chapter and

starts the execution environment and development environment packages installer.

Please see the Help folder in the installed hardware installation instructions please see reference in help

disk attachments or downloaded from CONTEC’s Web site development environment.

Furthermore, that applies to the default step 4 software described below, see config.chm folder

installed execution environment.

CAUTION

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды