CRX1
Single Zone
Wireless Controller
•
Places where the sun will shine on it.
•
Places where, for example, it could be hit by a door.
•
Places where it may get wet.
Fixing CRX1 to the wall
Remove the wall plate from the rear of the CRX1 and mark through
the screw holes on the rear. Drill and plug the wall to accept No. 6 or
No. 8 screws and mount the wall plate. Attach the CRX1 back onto
the wall plate and tighten up the screws below.
Using CRX1 with supplied table top stand
CRX1 comes with a table top support that can be screwed to the
back of the unit, allowing it to stand upright on most flat surfaces.
Basic operation
Before you can use CRX1, it has to be activated by tapping any
control icons. The LCD screen backlight will turn on upon activation.
To operate any control icon, tap within 2 seconds of CRX1
activation. As the CRX1 does not have any pre-set programming,
you will need to set the day, time and day programmes. To enter
any programming mode, touch and hold for 5 seconds.
Setup menu
1. Touch and hold and icons together for 10 seconds.
2. The CRX1 will enter the setup menu.
3. Use and to change a value.
4. Use to scroll between the settings.
01 – temperature calibration
The temperature reading has been factory calibrated but if for any
reason it needs adjusting (better accuracy required, to suit different
position in the room etc.) the reading can be recalibrated in 0.5
degrees steps.
02 – change between degrees Celsius or Fahrenheit
03 – set maximum temperature
04 – set minimum temperature
(- - - = heating OFF, 4deg = frost protection)
05 - information about the software version
Choosing a position in the room
The CRX1 should be positioned in the same room as the heater. It
should be where its temperature will not be changed by local effects.
Avoid:
•
Draughty places near windows, doors and vents.
•
Places near the heater itself or any other heat sources in the room.
Please read this guide carefully and retain for future use
and maintenance.
Overview
The CRX1 is a wireless thermostat giving high precision room
temperature control. It is also a 7 day programmer with up to 6
temperature settings per day. Each CRX1 can control any number
of heaters in the same room (zone).
Batteries
Remove the CRX1’s battery cover and insert 2 new high quality
alkaline AAA batteries.
Warning
: Consort is not responsible for damage due to corrosion.
Battery leakage will cause permanent damage. To help avoid this:
•
Replace the batteries annually, even if there is not a low battery
warning. Remove failing or flat batteries immediately.
•
Always fit a pair of new high quality alkaline batteries from the
same pack. Never mix new and old batteries, or batteries of
different brands or types.
•
Never attempt to revive alkaline batteries by heating, crushing or
recharging.
Note:
The clock has to be set after replacing the batteries. All
other settings are unaffected.
Pairing CRX1 with heaters
This must be done, otherwise the heater will not work.
Set heater into pairing mode.
1. Turn the power to the heater on. Count 4 seconds, turn power
OFF.
2.
Turn the heater back ON, the light should be flashing green.
(If the light isn’t flashing green, the 4 seconds timing was
incorrect. Repeat step 1.)
3. The heater is now ready for pairing with CRX1.
This has to be done within 30 seconds. After 30 seconds the heater
will return to normal operating mode.
Set CRX1 into pairing mode.
1. Touch and hold and icons together for 10 seconds.
2. The display will show the CRX ID number.
3.
Tap the button while the light on the heater is flashing
green.
If the pairing was successful, the light will stop flashing and the
heater is paired with CRX1. This has to be done within 30 seconds.
After 30 seconds, the CRX1 will return to normal operating mode.
Installation and Control Guide for
Getting to know your CRX1 wireless controller
day
programme number in
SETB & PROG mode
time
set temperature
programming options
battery capacity
operating mode
An illustration of functions available on CRX1.
heater active symbol
alarm notification
room temperature
fan
radio transmit symbol
child-lock
control icons
: set time, day and accessing programming menu
: activate fan function (for fan heaters only)
: select operating mode
: increase value
: decrease value
ALARM!
: flashes to indicate error in temperature settings for the
day e.g. the timing set for 2nd temperature setting precedes the
1st temperature setting.
