CLEANING THE RECOVERY TANK FILTERS
In order to clean the filters present inside the recovery tank, do the following:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
”).
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
3. Grip the moulded handles (1) on the recovery tank cover (
Fig.1
).
4.
Turn the recovery tank cover until the support (2) fixed to the recovery tank is coupled with the
pin (3) fixed to the recovery tank cover (
Fig.2
).
5.
Remove the dirty water basket/filter (4) from the support (
Fig.3
).
6.
Remove the basket cover (5) from the basket/filter (4) (
Fig.4
).
7.
Clean the basket/filter (4) and the basket cover (5) under a jet of water.
NB
: Use a spatula or brush to eliminate any dirt that is particularly difficult to remove.
8.
Use a dry cloth to dry the basket/filter (4) and the basket cover (5) and place them back inside
the recovery tank.
9.
Remove the vacuum motor filter (6) and the basin (7) from the support (
Fig.5
).
10. Clean the basin (7) under a jet of water.
11.
Extract the dirt present inside the vacuum motor's filter (6).
N.B.
: Use a jet of water to eliminate any remaining dirt, and use a spatula or a brush with soft
bristles to eliminate any dirt that is particularly hard to remove.
12.
Wait for the vacuum motor's filter to dry, if necessary, and then place it back on its support.
ATTENTION
: Wait for the filter to dry completely before using it again, or else use a spare.
13.
Remove the vacuum motor's duct filter from its support (8) (
Fig.6
).
14.
Clean the vacuum motor's duct filter under a jet of water (8).
N.B.
: Use a spatula to eliminate any dirt that is particularly difficult to remove.
15.
Dry the vacuum motor's duct filter with a dry cloth (8) and place it back on its support.
16.
Clean the lower part of the vacuum cover with a damp cloth, and carefully clean the filter gaskets
(
Fig.7
).
17. Grip the handle (1) and turn the recovery tank's cover to its working position.
To clean the recovery tank filters with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Check that the brush head body is in its rest position. If this is not the case, turn the brush head
control lever (1) anticlockwise (
Fig.1
) so that the brush head body lifts up off the floor.
3. Check that the squeegee body is in its rest position. If this is not the case, turn the squeegee
head control lever (1) clockwise (
Fig.2
), so that the squeegee head body lifts up off the floor.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Go to the front right of the machine.
5. Stand at the back of the machine.
6. Grip the moulded handles (3) on the recovery tank cover (
Fig.3
).
3
2
1
1
4
2
3
5
6
7
6
8
4
5
7
3
1
2
1
2
3
7.
Turn the recovery tank cover until the support (4) fixed to the recovery tank is coupled with the
pin (5) fixed to the recovery tank cover (
Fig.4
).
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
8. Release the tank cleaning accessory (6) (at the back of the machine) from the retainers (
Fig.5
).
9. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (7) on the steering
column of the machine (
Fig.6
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
N.B.
: Before starting the optional tank cleaning kit, check the level indicator (8) to see how
much solution there is in the solution tank (
Fig.8
).
10. Activate the solution jet by pressing the lever in the tank cleaning accessory.
N.B.
: To adjust the solution jet from the
tank cleaning accessory, turn the knob (9) on the
accessory itself
(
Fig.8
).
N.B.
: To adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob
(10) on the accessory itself
(
Fig.9
).
N.B.
: To stop the solution jet,
use the lever (11) on the tank cleaning accessory (
Fig.10
).
11.
Remove the dirty water basket-filter from the support (12) (
Fig.11
).
12.
Remove the basket cover (13) from the basket-filter (12) (
Fig.12
).
13.
Using the spray gun, clean the basket-filter (12) and the basket cover (13).
N.B.
: Use a spatula or brush to eliminate any dirt that is particularly difficult to remove.
14.
Use a dry cloth to dry the basket/filter (12) and the basket cover (13) and place them back inside
the recovery tank.
15.
Remove the vacuum motor filter (14) and the basin (15) (
Fig.13
).
16. Clean the basin (15) under a jet of water.
17.
Extract the dirt present inside the vacuum motor's filter (14).
N.B.
: Use a jet of water to eliminate any remaining dirt, and use a spatula or a brush with soft
bristles to eliminate any dirt that is particularly hard to remove.
18.
Wait for the vacuum motor's filter to dry, if necessary, and then place it back on its support.
ATTENTION
: Wait for the filter to dry completely before using it again, or else use a spare.
19.
Remove the vacuum motor's duct filter from its support (16) (
Fig.14
).
20.
Using the spray gun, clean the vacuum motor duct filter (16).
N.B.
: Use a spatula to eliminate any dirt that is particularly difficult to remove.
21.
Dry the vacuum motor's duct filter with a dry cloth (16) and place it back on its support.
22.
Clean the lower part of the vacuum cover with a damp cloth, and carefully clean the filter gaskets
(
Fig.15
).
4
4
5
5
6
6
7
9
10
8
9
7
8
11
12
13
12
10
11
15
14
16
13
14
15
28
