Connect IT CI-26 Скачать руководство пользователя страница 1

This product is designed to mount flat panel televisions weighing up to 75kg/165lbs to a vertical firm wall. 

Safety Warning:

 Be careful to make sure there are no missing or defective parts. Never use defective parts. Improper 

installation may cause damage or serious injury. 

Note:

 The included hardware is for mounting on walls . If you are uncertain about the nature of your wall, consult an 

expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The 

supplied hardware is not for steel. 

Forbidden Instruction:

  Do not mount onto plasterboard or panelled walls.

ASSEMBLY INSTRUCTIONS 

FOR TILTING FLAT PANEL WALL MOUNT

1

2

3

Mounting the Wooden Wall Plate

Important! For safety, the mount must be secured to two 
adjacent wood studs an least 40 cm  apart.
1. Using a stud finder, locate and mark two adjacent studs 
    for securing the mount.
2. Place the wall plate against the wall and level it using the 
    bubble guide.
3. Make two locations (two per stud) on the wall where the 
    mount will be secured.
4. Remove the wall plate and drill a (4mm) pilot hole an each 
    location using an electric drill.
5. With the help of another person, replace the wall plate and fix
     it to the wall using the Lag Bolts and Lag Bolt washers provided.
6. Do not over-tighten the bolts and do not release the wall plate until all screws are secure.

Mounting the Concrete Wall Plate 

1. Place the wall plate against the wall and level it using the bubble guide.
2. With the help of another person, mark off four (4) locations for fixing the 
    mount to the wall. 
3. Place the wall plate aside and drill a hole at each location using a 3/8" 
        (10mm) masonry bit. Remove any excess dust form the holes.
                 4. Insert one Concrete Anchor into each hole. A hammer can be 
                     used to lightly tap the anchors into place if necessary. 
                     5. With the help of another person, replace the wall plate 
                        and fix it to the wall using the Lag Bolts and Lag Bolt 
                        Washers provided.
                    6. Do not over-tighten the bolts and do not release the wall 
                        plate until all screws are secure.

Final Installation and Adjustment

1. With the help of another person, carefully lift your display and place it on the wall plate. Do not release the display until the 

mounting arms have securely hooked onto the mount.

2. Move the safty screws to the position as the picture shows . 

Attaching the Arms to the Display

Important! Use extra care during this part of the installation. If possible, avoid placing your display face down as it may 

damage the viewing surface. Note: Your mount comes with a selection of bolt diameters and lengths to accommodate a 

wide variety of display models. Note all o f the hardware in the kit will be used.

1. Determine the correct length of bolt to use with your display by first examining the back of you display.

A. If your display has a flat back, you will use one of the shorter bolts from the hardware kit.

B. If your display has a curved or recessed back, you will use one of the longer bolts along with a spacer.

2. Determine the correct diameter of bolt to use by carefully trying one bolt each from the hardware kit. Do not force any 

of the bolts-if you feel resistance stop immediately and by a smaller diameter bolt.

3. Attach the arms to the back of your display using the bolts identified along with corresponding washers.

A. If you are using the M4 or M5 bolts, you will also need to use the small hole of the washers  n  . If you are using the M6 

or M8 boles, you will also need to use the big hole of the washers  n  .

B. If you are using one of the longer bolts on a display with a curved recessed back, you will also use a Spacer. Use the 

Small Spacer for M4 and M5 bolts and the Large Spacer for M6 and M8 bolts.

4. Make sure all screws are secure, but do not over-tighten them.

5. Knobs should face the outside of the television

Hardware kit

Diagram-1

Diagram-2

Diagram-3

Diagram-6

Diagram-5

Diagram-4

Diagram-7

Diagram-8

40cm  

o

k

j

k

o

SUPPLIED PARTS: 

Supplied joint parts are exclusive for using in this product. Other joint parts are forbidden to use on this product. If any parts are 

missing or faulty, telephone the special franchiser for a placement.

M4x30mm Screw

x4

Big Spacer

x4

M5x30mm  Screw 

M6x30mm  Screw 

M8x25mm  Screw 

M8x40mm  Screw 

Concrete Anchor

6mm Lag Bolt

Small Spacer

Lag Bolt Washer

Washer

x4

x4

x4

x4

x4

a

b

d

e

f

g

h

i

x4

x4

x4

j

k

l

x4

M4x12mm Screw

M5x12mm  Screw 

M6x12mm  Screw 

x4

x4

x4

m

n

o

CI-26

Отзывы: