Congatec XTX conga-XLX Скачать руководство пользователя страница 63

Страница: 63 / 72

Feature

Options

Description

LPC DRQ Routing

Onboard Super I/O

External LPC Device

Select if LPC DRQ line should be routed to the onboard Super

I/O or the external LPC Device. If the onboard floppy drive or the

ECP parallel port is enabled, the LPC DRQ has to be routed to

the onboard Super I/O controller.

Network Controller

Disabled

Enabled

Enables/Disables the onboard PCI network controller.

System Beeper

Disabled

Enabled

Enables/Disables the external system beeper.

8.5.6 External Super I/O Configuration Submenu

Feature

Options

Description

External Super I/O

Configuration Submenu

No Option

Floppy Support

Enabled

Disabled

Enables/Disables floppy device of the external Super I/O controller.

Note: The external Floppy only can be used, if the onboard Floppy
is disabled. Otherwise the there is a resource conflict.

Serial Port 1

Disabled

3E8/IRQ11

3E8/IRQ10

2E8/IRQ11

2E8/IRQ10

Specifies the I/O base address and IRQ of the serial port 1 of the

external Super I/O controller.

Serial Port 2

Disabled

3E8/IRQ11

3E8/IRQ10

2E8/IRQ11

2E8/IRQ10

Specifies the I/O base address and IRQ of the serial port 2 of the

external Super I/O controller.

Parallel Port

Disabled

378

278

3BC

Specifies the I/O base address used by the parallel port of the

external Super I/O controller.

Parallel Port Mode

SPP

EPP 1.7

EPP 1.9

ECP

Specifies the parallel port mode of the external Super I/O controller.

Parallel Port IRQ

Disabled

IRQ5

IRQ7

Specifies the interrupt for the parallel port of the external Super I/O

controller.

Parallel Port DMA

Disabled

DMA1

DMA3

Specifies the DMA channel for parallel port in ECP mode.

Note

This submenu is only available if an external Winbond W83627HG Super I/O controller
is present in the system. The configuration base I/O address of the Super I/O has to be
0x4E and 0x4F.

X800m12

63/72

Содержание XTX conga-XLX






































































Результаты поиска

Содержание XTX conga-XLX

Отзывы:

Бренды по названию

Популярные бренды

Congatec XTX conga-XLX, Руководство пользователя

Результаты поиска

Содержание XTX conga-XLX

Отзывы:

Бренды по названию

Популярные бренды