manualshive.com logo in svg

Congatec XTX conga-XLX, Руководство пользователя

Поделиться
Скачать
Congatec XTX conga-XLX Скачать руководство пользователя страница 56

8  BIOS Setup Description

The following section describes the BIOS setup program. The BIOS setup program can 
be used to view and change the BIOS settings for the module. Only experienced users 
should change the default BIOS settings.

8.1  Starting the BIOS setup program

The BIOS setup program is accessed by pressing the <DEL> key during POST.

8.1.1  Manufacturer Default Settings

Pressing the <End> key repeatedly immediately after power is initiated will result in the 
manufacturer default settings being loaded for that particular boot sequence and only 
that boot sequence. This is helpful when a previous BIOS setting is no longer desired.

8.2  Setup Menu and Navigation

The   congatec   BIOS   setup   screen   is   composed   of   main   frames,   with   submenu 
selections.  The   main   frame   displays   all   the   options   that   can   be   configured   in   the 
selected menu. Grayed-out options cannot be configured, only the highlighted options 
can be configured. An option setting can be chosen by pressing the ↑↓Up/Down keys. 
The actual available setting is displayed on the right side of the option. The bottom line 
of   the   frame   displays  a  short   help  text   related   to   the   option.   These   text   messages 
explain the options and the possible impacts when changing a setting of the selected 
option in the frame. The setup program uses a key-based navigation system. Most of 
the keys can be used at any time while in setup. The table below explains the supported 
keys:

Note

Entries in the option column displayed in bold print indicate BIOS default values.

Key

Description

← → Left/Right

Select a setup item or sub menu.

↑ ↓ Up/Down

Select a setup item or sub menu.

+ - Plus/Minus

Change the field value of a particular setup item.

Tab

Select next item.

F1

Display General Help screen.

<L>

Load optimal default settings. (only valid in main menu)

<S>

Save changes without exit setup. (only valid in main menu)

<X>

Save changes and exit setup. (only valid in main menu)

<Q>

Discard changes and exit setup. (only valid in main menu)

ENTER

Set an option of a particular setup item or enter sub menu.

ESC

Confirm changes of the actual menu/submenu and go to next menu. 

Copyright © 2006 congatec AG 

X800m12

56/72

Содержание XTX conga-XLX









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды