manualshive.com logo in svg

Congatec XTX conga-XLX, Руководство пользователя

Поделиться
Скачать
Congatec XTX conga-XLX Скачать руководство пользователя страница 55

7.6  PCI Interrupt Routing Map

Table 42

PCI Interrupt Routing Map

PCI Bus INT line 
(see note below)

Geode LX800

Companion
CS5536

Ethernet
RTL8100C

SATA
VT6421

PATA
VT6421

INTA

x

x

INTB

x

INTC

x

x

x

INTD

x

x

Note 

These interrupts are available for external devices/slots via the X1 connector.

7.7  PCI Bus Masters

The  conga-XLX  supports four  external PCI Bus Masters.  There  are no limitations in 
connecting bus master PCI devices.

Note

If   there   are   two   devices   connected   to   the   same   PCI   REQ/GNT   pair   and   they   are  
transferring data at the same time then the latency time of these shared PCI devices  
can not be guaranteed. 

7.8  I²C Bus

There are no onboard resources connected to the I²C bus. Address 16h is reserved for 
congatec Battery Management solutions.

7.9  SM Bus

System Management (SM) bus signals are connected to the AMD Geode™ CS5536 
companion device and the SM bus is not intended to be used by off-board non-system 
management   devices.   For   more   information   about   this   subject   contact   congatec 
technical support.

7.10  LPC Bus

Low Pin Count bus signals are connected to the AMD Geode™ CS5536 companion 
device and are available on the X2 connector of the XTX module. The LPC bus can be 
used to interface an off-board non-system LPC device like a Super I/O. There is only 
the configuration base address 4Eh/4Fh available to access an off-board LPC devices. 
For more information about this subject contact congatec technical support.

Copyright © 2006 congatec AG 

X800m12

55/72

Содержание XTX conga-XLX









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды