manualshive.com logo in svg

Congatec XTX conga-XLX, Руководство пользователя

Поделиться
Скачать
Congatec XTX conga-XLX Скачать руководство пользователя страница 28

5  Additional Features

5.1  Watchdog

The conga-XLX is equipped with a multi stage watchdog. This solution can be triggered 
by software and external OEM hardware (input pin is pin 48 on the X2 connector called 
WDTRG#).   For   more   information   about   the   Watchdog   feature   see   the   BIOS   setup 
description section 8.5.8

 

of this document and application note AN3_Watchdog.pdf on 

the congatec AG website at www.congatec.com.

5.2  Onboard Microcontroller

The conga-XLX is equipped with an ATMEL Atmega88 microcontroller. This onboard 
microcontroller plays an important role for most of the congatec BIOS features. It fully 
isolates some of the embedded features such as system monitoring or the I²C bus from 
the x86 core architecture, which results in higher embedded feature performance and 
more reliability, even when the x86 processor is in a low power mode.

5.3  Embedded BIOS

The   conga-XLX   is   equipped   with   congatec   Embedded   BIOS   and   has   the   following 
features:

•

ACPI Power Management

•

ACPI Battery Support

•

Supports Customer Specific CMOS Defaults

•

Multistage Watchdog

•

User Data Storage

•

Manufacturing Data and Board Information

•

OEM Splash Screen

•

Flat Panel Auto Detection

•

BIOS Setup Data Backup

•

Fast Mode I²C Bus

•

Real Headless Operation

Note

The   conga-XLX   embedded   BIOS   is   based   on   the   Insyde   Xpress   ROM   BIOS   and 
therefore does not support 'System Plug and Play' mechanism.

Copyright © 2006 congatec AG 

X800m12

28/72

Содержание XTX conga-XLX









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды