Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 58

Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 56

Copyright

©

2022

congatec

GmbH

CET0m10

56/58

6.3

Debug Display

The conga-MEVAL provides four 7-segment displays (D37-D39, D41) for post code or debug information. Use the tables below to configure
the post code decoding process.

A list of the BIOS POST codes and associated POST test and initialization routines for congatec COM Express™ modules is available at
www.congatec.com.

Table 57 X63 - POST Code Decoder

Pins

Configuration

1 - 2

Port 80h and port 84h (default)

2 - 4

Port 80h and port 81h

3 - 4

Port 80h and port 90h

5 - 6

Port 90h and port 94h

Connector Type

X63: 2.54 mm grid jumper

6.4

Ground Test Points

The conga-MEVAL provides four test points (M1-M4). These test points are connected to ground and they make it easier to connect oscilloscope
probes or multimeter lines or both to ground during measurements.

X63

2

1

3

5

6

4

D37 D38 D39 D41

M1-M4

«
...
54
55
56
57
58
»

Содержание COM Express conga-MEVAL



























































Отзывы:

Нет отзывов