manualshive.com logo in svg

Congatec COM Express conga-MEVAL, Руководство пользователя, Страница: 51 / 58

Поделиться
Скачать
Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 51

Copyright 

© 

2022 

congatec 

GmbH 

 

      CET0m10 

       

51/58

5.19 

Smart Battery Header

The conga-MEVAL provides SBM header X52 for attaching smart battery module kits. Use jumpers X80 and X81 to select the communication 
bus for the smart battery.

Table 53   X52 - SBM Header Pinout

Pin Signal

Pin Signal

1

I2C/SMB_CLK

2

I2C/SMB_DAT

3

PWRBTN#

4

BATLOW#

5

PS_ON#

6

SUS_S45# 

1

7

VCC (5V)

8

5V_SB

9

SUS_STAT#

10

GND

Table 54   X80/X81 - Bus Selection

Pin X80

X81

Description

1-2

I2C bus data signal

I2C bus clock signal

Select I2C bus for smart battery (default)

2-3

SM bus data signal

SM bus clock signal

Select SM bus for smart battery

 

Note

1

 The signal “SUS_S45#” represents a “logical ANDing” of signals SUS_S4# and SUS_S5#

 

Connector Type

X52: 2.54 mm, 2 x 10-pin grid female

X80, X81: 2.54 mm grid jumper 

5.20 

Programming Header - Internal Use Only

Connector X73 is for programming the congatec board controller. This connector is designed for internal use only.

 

Connector Type

X73: 2.54 mm, 2 x 10-pin female header

10

8

9

7

6

5

4

3

2

1

X52

2

3

1

X80/X81

X73

2

1

3

5

6

7

8

9

10

4

Содержание COM Express conga-MEVAL



























































Отзывы:

Нет отзывов