Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 58

Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 28

Copyright

©

2022

congatec

GmbH

CET0m10

28/58

5.5

SD Card Slot

The conga-MEVAL features a full-size SD card slot X108.

The slot is routed to the module’s SDIO interface, which is multiplexed with GPIO. The

shared signals are demultiplexed and routed to either the SD card slot (SDIO mode) or the feature connector X53 (GPIO mode).

Use jumper X22 to select SDIO or GPIO mode.

Table 18 X22 - SDIO/GPIO Connection

Pin

Description

1-2

SDIO mode

2-3

GPIO mode (default)

Connector Type

X22: 2.54 mm grid jumper

X108: SD card

5.6

Display Interfaces

The conga-MEVAL provides the following display interfaces:

•

Disp+

•

eDP

•

LVDS

5.6.1

DP++

The conga-MEVAL provides a DisplayPort interface on connector X106. The DP++ port is routed through DisplayPort re-driver to support HBR3
data rate (up to 12 Gbps)

.

You can connect a DP++ to HDMI dongle to the DP++ connectors if your module supports it.

Connector Type

X106: Standard DP cable

2

3

1

X22

X108

X106

«
...
26
27
28
29
30
...
»

Содержание COM Express conga-MEVAL



























































Отзывы:

Нет отзывов