manualshive.com logo in svg

Congatec COM Express conga-MEVAL, Руководство пользователя, Страница: 22 / 58

Поделиться
Скачать
Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 22

Copyright 

© 

2022 

congatec 

GmbH 

 

      CET0m10 

       

22/58

 

Note

1.  With variable power input, you can measure the module power. To enable variable voltage power to the module, the conga-MEVAL power 

must be on.

2.  The conga-MEVAL supplies the module with a standby voltage if available.

 

Connector Type

X76: 2.54 mm grid jumpet

M29/M30: 

4 mm diameter banana plug 

5.2.4 

Status LEDs

The status LEDs show the different power states of the conga-MEVAL. Refer to the following table for detailed information.

Table 11   Power LEDs Status

LED Status Description

All

Off

No power applied.

All

On

ATX power supply is fully switched on, with stable 3.3 V, 5 V and 12 V.

D64

On

The green LED indicates that power is delivered to the COM Express module

D34

On

The green LED indicates that 12 V main power is present

D35

On

The green LED indicates that 5 V main power is present

D36

On

The green LED indicates that the onboard 3.3 V main power is present

D40

On

The green LED indicates that the 1.5 V power is present

D42

On

The yellow LED indicates that the onboard 3.3 V standby power is present

D33

On

The yellow LED indicates that 5V standby power is applied to the conga-MEVAL.

 

If D33 and D42 are lit, it 

indicates the ATX power supply is mechanically switched on.

Содержание COM Express conga-MEVAL



























































Отзывы:

Нет отзывов